background image

0-5

InTroDuCTIon

DangEr

Suspension of a load from a single rope could cause the load to start rotating and consequently cause the rope 

strands to untwist or the load to slip; this could lead to serious injury.

l

Never lift a heavy load when the two legs of the ropes form a wide angle. the permitted load (kg) decreases in inverse propor

-

tion to the angle of suspension; the table below indicates how the permitted load varies according to the angle of suspension 

for two Ø 10 mm ropes each with a load capacity of 1000 kg.

Fig. 1

0.1.5 - Tightening torques

bolts and nuts

DangEr

The tightening torques for certain specific components and special tightening methods are indicated in the relative 

assembly paragraphs.

The tightening torques indicated below refer to screws and nuts assembled without lubrication and, where applicable, with anaerobic 

threadlocking compound. the values apply to tightening on steel or cast iron components; for soft materials such as aluminium, cop

-

per, plastic, sheet metal or panels, the indicated tightening torques must be reduced by 50%.

Table 2

bolT sIZE

bolT Class

8.8

10.9

12.9

Nm

lb.ft.

Nm

lb.ft.

Nm

lb.ft.

M6x1

8.0 – 8.8

5.9 – 6.5

11.8 – 13.0

8.7 – 9.6

13.8 – 15.2

10.2 – 11.2

M8x1.25

19.4 – 21.4

14.3 – 15.8

28.5 – 31.5

21.0 – 23.2

33.3 – 36.9

24.5 – 27.2

M10x1.5

38.4 – 42.4

28.3 – 31.2

56.4 – 62.4

41.6 – 46.0

67.4 – 74.4

49.7 – 54.8

M12x1.75

66.5 – 73.5

49.0 – 54.2

96.9 – 107

71.4 – 78.9

115 – 128

84.8 – 94.3

M14x2

106 – 117

78.1 – 86.2

156 – 172

115.0 – 126.8

184 – 204

135.6 – 150.3

M16x2

164 – 182

120.9 – 134.1

241 – 267

117.6 – 196.8

282 – 312

207.8 – 229.9

M18x2.5

228 – 252

168.0 – 185.7

334 – 370

246.2 – 272.7

391 – 432

288.2 – 318.4

M20x2.5

321 – 355

236.6 – 261.6

472 – 522

347.9 – 384.7

553 – 611

407.6 – 450.3

M22x2.5

441 – 487

325.0 – 358.9

647 – 715

476.8 – 527.0

751 – 830

553.5 – 611.7

M24x3

553 – 611

407.6 – 450.3

812 – 898

598.4 – 661.8

950 – 1050

700.2 – 773.9

M27x3

816 – 902

601.4 – 664.8

1198 – 1324

882.9 – 975.8

1419 – 1569

1045.8 – 1156.4

Summary of Contents for R7.190 DCR










































Reviews: