LAMAR CA-1550-CML Instruction Manual Download Page 38 | Manualshive

Page: 38 / 44

background image

6. TROUBLE-SHOOTING

Problem Possible Cause Corrective Action

F. Discharge current

immediately surges to a
high value and blows DC
discharge fuses even
though the current adjust
knob is set low

Reversed polarity of battery
connection

Ensure that polarity is respected
on battery connection. If
connector has been removed
ensure that DC leads are not
reversed.

Defective discharge power
control module

With AC voltage and battery
disconnected, open unit and
remove heavy leads from
terminals on black 1”x1”
(25mmx25mm) power module.
Check resistance between
terminals with ohmmeter. If short
circuit, call Power Products
technical support.

G. The DC charge fuse

blown

Reversed polarity of battery
connection

Ensure that polarity is respected
on battery connection. If
connector has been removed
ensure that DC leads are not
reversed.

Defective charge power control
module

With AC voltage and battery
disconnected, open unit and
remove ACL leads from terminals
on black 1¾”x2¼”
(45mmx60mm) power module
(G1 and G2 tabs included).
Check resistance b and
– terminals with ohmmeter. If
short circuit, call Power Products
technical service.

CA-1550 CHARGER / ANALYZER – OPERATING MANUAL LI-4159-CML Rev A

Page 35

«
...
36
37
38
39
40
...
»

Summary of Contents for CA-1550-CML













































Reviews:

No comments

Related manuals for CA-1550-CML

Brand: Deka Pages: 12

Brand: Elettro CF Pages: 20

Brand: Phonocar Pages: 12

Brand: Gacell Pages: 12

LFeLi-48 Series

Brand: LEOCH Pages: 40

Brand: Streetwize Pages: 2

Brand: Hoover Pages: 2

Brand: Kärcher Pages: 84

Brand: Exibel Pages: 5

Brand: XU1 Pages: 2

Lewden ASPEN Series

Brand: Palazzoli Pages: 37

Brand: Hubble Pages: 15

Brand: BTI Pages: 48

Brand: Hitachi Pages: 12

Brand: Hitachi Pages: 3

Brand: Hitachi Pages: 24

Brand: Hitachi Pages: 32

Brand: Hitachi Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands