LAMAR CA-1550-CML Instruction Manual Download Page 35 | Manualshive

Page: 35 / 44

background image

5. CALIBRATION AND MAINTENANCE

EXTERNAL CALIBRATED MILLIVOLTMETER

Figure 5-3. Circuit diagram for shunt verification

5.5

DISCHARGE CURRENT OPERATING RANGE

The CA-1550’s factory preset max discharge rate of amperes can be increased past
50 amperes. If necessary to increase the discharge rate please contact the factory.

5.6

MAINTENANCE

Standard electrical equipment maintenance and cleaning procedures should be
followed.

5.6.1

VENTS AND FAN

Regularly check that the fan vent next to the front panel is clean to ensure
adequate cooling of the unit. This is especially important when the unit is placed in a
dusty or otherwise dirty air environment.

5.6.2

DC BATTERY CABLE AND LEADS

Inspect DC battery cable and connector periodically. Replace damaged or worn
cable.

WARNING: Disconnect AC voltage and battery before
attempting to replace or secure cable.

CA-1550 CHARGER / ANALYZER - OPERATING MANUAL LI-4159-CML Rev A

Page 32

«
...
33
34
35
36
37
...
»

Summary of Contents for CA-1550-CML













































Reviews:

No comments

Related manuals for CA-1550-CML

Brand: oaniso Pages: 26

Brand: Sennheiser Pages: 28

NauticBattery NA-12Li125BL

Brand: UPOWER Ecoline Pages: 5

V-CHARGE 100 DUO

Brand: VOLTCRAFT Pages: 236

Brand: GreenWorks Pages: 16

Brand: H-Speed Pages: 54

Brand: Carp Sounder Pages: 8

Brand: HONGKONG BWAY INDUSTRIAL Pages: 3

Ultegra SM-BCR1

Brand: Shimano Pages: 2

Brand: Shenzhen Xinkeying Technology Pages: 5

Brand: protech Pages: 4

Brand: Orderman Pages: 10

Brand: Elinta Pages: 2

Brand: Carbest Pages: 18

Brand: CEN-TECH Pages: 12

Innotec MBC 12-25/3

Brand: Studer Pages: 46

Brand: Chauvet Pages: 16

Brand: Topdon Pages: 88

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands