background image

2

Model 240 Quick Start Guide

Safety Precautions

Observe these general safety precautions during all phases of 
instrument operation, service, and repair. Failure to comply with 
these precautions or with specific warnings in the user’s manual 
violates safety standards of design, manufacture, and intended 
instrument use. Lake Shore Cryotronics, Inc. assumes no liability 
for customer failure to comply with these requirements.

The 240 Series input module protects the operator and 
surrounding area from electric shock or burn, mechanical 
hazards, excessive temperature, and spread of fire from the 
instrument. Environmental conditions outside of the conditions 
below may pose a hazard to the operator and surrounding area.

 

„

Indoor use

 

„

Altitude to 2000 m

 

„

Temperature for safe operation: -20 °C to 50 °C

 

„

Maximum relative humidity: 95% non-condensing

 

„

Power supply voltage fluctuations not to exceed  
±10% of the nominal voltage

 

„

Overvoltage category II

 

„

Pollution degree 2

 

„

IP20: not protected against harmful ingress of water 

 

Ground the instrument

 

To minimize shock hazard, the instrument is equipped with a 
grounded connection to the DIN rail. Connect the DIN rail to an 
electrical ground.

Do not operate in an explosive atmosphere

 

Do not operate the instrument in the presence of flammable gases or 
fumes. Operation of any electrical instrument in such an environment 
constitutes a definite safety hazard.

Do not substitute parts or modify instrument

 

Do not install substitute parts or perform any unauthorized 
modification to the instrument. Return the instrument to an 
authorized Lake Shore Cryotronics, Inc. representative for service and 
repair to ensure that safety features are maintained.

Cleaning

 

Do not submerge instrument. Clean only with a damp cloth, 
exterior only.

Installation

 

When installing the instrument, ensure it is mounted securely on the 
DIN rail.

Improper Use

 

If the instrument is used in a manner that is not specified by Lake 
Shore, the safety protections provided by the instrument are no 
longer guaranteed, and may be impaired.

For more safety information, refer to the Model 240 user’s manual:  

https://www.lakeshore.com/240manual

.

Summary of Contents for 240













Reviews: