background image

 

10HP Bag Filter Dust Collector Manual 

4

 

5. Do not use with damaged cord or plug. If appliance is not working as it 

should, has been dropped, damaged, left outdoors, or dropped into water, 

return it to a service center. 

 

6. Do not pull or carry by cord, use cord as a handle, close a door on cord, or 

pull cord around sharp edges or corners. Do not run appliance over cord. 

Keep cord away from heated surfaces. 

7. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord. 

8. Do not handle plug or appliance with wet hands. 

9. Do not put any object into openings. Do not use with any opening blocked; 

keep free of dust, lint, hair, and anything that may reduce air flow. 

10. Keep hair, loose clothing, fingers, and all parts of body away from 

openings and moving parts. 

11. Turn off all controls before unplugging. 

12. Use extra care when cleaning on stairs.  

13. Do not use to pick up flammable or combustible liquids, such as gasoline, 

or use in areas where they may be present. 

14. Connect to a properly grounded outlet only. See Grounding Instructions. 

 

SAVE THESE INSTRUCTIONS 

 

1.

 

Read and understand the warnings posted on the machine and in this 

manual. Failure to comply with all of these warnings may cause 

serious injury. 

 

2.

 

Replace the warning labels if they become obscured or removed. 

 

3.

 

This Dust Collector is designed and intended for use by properly 

trained and experienced personnel only. If you are not familiar with 

the proper and safe operation of this type of dust collector, do not use 

until proper training and knowledge have been obtained. 

 

4.

 

Do not use this machine for other than its intended use. If used for 

other purposes, LAGUNA TOOLS INC., disclaims any real or implied 

warranty and holds itself harmless from any injury that may result 

from that use. 

 

5.

 

Always wear approved safety glasses/face shields while using this 

machine. 

 

6.

 

Before operating this dust collector, remove tie, rings, watches and 

other jewelry, and roll sleeves up past the elbows. Remove all loose 

clothing and confine long hair. Non-slip footwear or anti-skid floor 

strips are recommended. Do not wear gloves. 

 

7.

 

Wear ear protectors (plugs or muffs) during extended periods of 

operation. 

 

Summary of Contents for iFlux 10 Elite

































Reviews: