background image

 

1HP One stage Dust Collector Manual 

3

 

IMPORTANT SAFETY INSTRUCTIONS 

 

 READ AND UNDERSTAND ALL WARNINGS AND 

OPERATING INSTRUCTIONS BEFORE USING THIS EQUIPMENT. Failure to 

follow all instructions listed below, may result in electric shock, fire, and/or 

serious personal injury or property damage. 

 

Woodworking can be dangerous if safe and proper operating procedures are 

not followed. As with all machinery, there are certain hazards involved with 

the operation of the product. Using the machine with respect and caution will 

considerably lessen the possibility of personal injury. However, if normal 

safety precautions are overlooked or ignored, personal injury to the operator 

may result. Safety equipment such as guards, push sticks, hold-downs, 

featherboards, goggles, dust masks and hearing protection can reduce your 

potential for injury. But even the best guard won’t make up for poor 

judgment, carelessness or inattention. Always use common sense and 

exercise caution in the workshop. If a procedure feels dangerous, don’t try it. 

Figure out an alternative procedure that feels safer. REMEMBER: Your 

personal safety is your responsibility.  

 

 This machine was designed for certain applications 

only. We strongly recommend that this machine not be modified and/or used 

for any application other than that for which it was designed. If you have any 

questions relative to a particular application, DO NOT use the machine until 

you have first contacted the manufacturer to determine if it can or should be 

performed on the product. 

 

If you have any questions relative to its application DO NOT use the product 

until you have contacted the manufacturer and we have advised you.  

 

When using an electrical appliance, basic precautions should always be 

followed, including the following: 

 

READ ALL INSTRUCTIONS BEFORE USING (THIS APPLIANCE) 

To reduce the risk of fire, electric shock, or injury: 

1. Do not leave appliance when plugged in. Unplug from outlet when not in 

use and before servicing. 

2. Do not use outdoors or on wet surfaces 

3. Do not allow to be used as a toy. Close attention is necessary when used 

by or near children. 

4. Use only as described in this manual. Use only manufacturer’s 

recommended attachments. 

Summary of Contents for BFLUX1

































Reviews: