10
1. Reference
REVO 1216 Lathe © 2018 Laguna Tools 10/22/2018
1.
Re
fe
re
nc
e
EN
1.4 Internal Map
Figure L003B: REVO 1216 Lathe internal map feature image.
(1)
Front Spindle Threading - 1"x 8 TPI.
(2)
Head-stock Front Bearing - 6006LLU.
(3)
Spring Loaded Spindle Lock.
(4)
RPM Sensor.
(5)
Ride Pulley Cat Screw.
(6)
Indexing
Positions.
(7)
Rear Bearing - 6005LLU
(8)
Below Hand Wheel, Rear Spindle Threading
- 1"x 8 TPI.
(9)
Hand Wheel
(10)
Indexing Plunge.
(11)
Viewing Window of Index
Position.
(12)
Drive Belt.
(13)
Cam Stop.
(14)
Cam Adjustment Bolt.
(15)
Belt
Release Cam Handle
(16)
High RPM Pulley 650 - 3500 RPM.
(17)
MED RPM Pulley
325 - 1750 RPM.
(18)
Low RPM Pulley 50 - 525 RPM.
Key Name
Description
1
Front Spindle
Threading
1" x 8 TPI. This can be used to fasten a faceplate or chuck with 1" x 8 TPI threading.
2
Front Bearing
6006LLU double sealed premium bearing. This bearing should last a very long time,
but can be replaced if needed.
3
Spindle Lock
Press to lock, stop pressing to unlock.
CAUTION! Do not start the lathe with the lock
engaged.
Key Name
Description
4
RPM Sensor
Works very similar to a Laser Tachometer to relay the ACTUAL rpm of the spindle.
5
Ride Pulley
Used to transfer power from motor to pulley to spindle to workpiece.
6
Indexing Positions 24 Positions on a 15 degree step.
7
Rear Bearing
6005LLU double sealed premium bearing. This bearing should last a very long time,
but can be replaced if needed.
8
Rear Spindle
Threading
1" x 8 TPI. For Outboard turning, the "Bed Extension & Outboard Turning Kit" must be
purchased. Mount the extension in outboard turning position, remove the (9) Hand
Wheel and instill on the (1) front spindle threading. Finally, flip the lathe in reverse
and fasten your outboard raw stock with the 3" faceplate.
9
Hand Wheel
Used to turn the spindle by hand.
10
Indexing Plunge
Rotate clockwise to engage, Counter clockwise to release. Locks the spindle on the
index position.
11
Viewing Window
To view the current indexing position.
12
Drive Belt
Used to transfer power from motor to pulley to spindle to workpiece.
13
Cam Stop
Allows for the cam handle to lift the Drive Pulley assembly and loosen the belt for
adjusting between speed groups.
14
Cam Adjustment
Bolt
This bolt is to be used to adjust the cam lever mechanism if found faulty.
NOTICE!
Do not adjust unless necessary!
15
Cam Handle
Engage to change the belt between the speed groups.
16
High RPM Pulley
650 - 3500 RPM
17
MED RPM Pulley
325 - 1750 RPM
18
Low RPM Pulley
50 - 525 RPM
1.5 Control & Display Elements
Fig L002 - REVO 1216 Control Panel.
(1)
On button (Power).
(2)
Off button.
(3)
Speed adjustment knob - CW to
increase, CCW to decrease.
(4)
DRO RPM Panel.
(5)
Forward / Reverse Control.
(6)
Indexing Adjustment.
(7)
3" Faceplate shown on reverse
spindle mount.
