background image

Adjustments 
Note. 

The machine has had all its functions calibrated at the factory, but due to 

shipping conditions, some movement may have taken place. This is 

unavoidable and it is therefore recommended that the following checks are 

made prior to starting production. As the machine is used some functions may 

move, and it is therefore good practice to become

 

know the process for 

adjusting the machine prior to production.  

 

Adjusting the drive belts. 

Depth scale digital 
read out 

Motor tension nuts 

The drive belts should be 

checked after running the 

machine for approximately 

10 hours. The belts bed into 

the pulleys and will slacken 

off slightly. If they are not 

adjusted slippage may accrue and this will cause early 

belt failure. There should be a 3/16” deflection when the 

belt is pressed with moderate finger pressure. 

To increase the tension on the belts, loosen the lower nuts 

and tighten the upper nuts. Ensure that both left and right 

hand nuts are tensioned the same amount. 

 

Note.

 To access the drive belts, remove the Belt guard.   

Drive belts 

Note. 

To access the motor, remove one of the side panels.  

Note.

 Disconnect the power to the machine prior to 

conducting machine adjustments or repairs. 

 
Setting the planer depth Scale digital read out. 
1.

 With the table locked, plane a piece of wood and 

measure the thickness. 

Do not move the table height or unlock the height 

adjustment after planing the wood. 

2. 

Set the depth scale to either inches or mm by 

pressing the 

mm/in

 button.

 

3. 

Press the 

set

 button and hold. The display will 

flash each digit in turn. 

4.

 Hold the 

set

 button in until the digit that requires 

 

21

Summary of Contents for Platinum Series











































Reviews: