background image

Chapter 4: Features and Safety Precautions 

 

Product Service 1-800-522-7658 

11 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
1.

 

Ergonomic Slope and Front 

of 20

° 

provides maximum visibility, and 

comfort, reduces glare, thereby minimizing operator fatigue. 

2.

 

Internal Depth of 23" and interior height of 22" 

provides necessary 

depth and height to support procedures and other auxiliary equipment 
without extending outside the non-ventilated enclosure. 

3.

 

Flush Sash 

has a wiping seal and features a spring-loaded latch for loading 

auxiliary equipment.  The sash pivots down for normal operation. 

4.

 

Electrical Pass-Through Iris 

allows electrical cords and data cords to pass 

through the back of enclosure.  The unit ships with solid plugs and the iris 
plugs are included with the User’s Manual for your convenience. 

5.

 

Fluorescent Light 

provides illumination for the interior of the enclosure. 

6.

 

Ultraviolet Germicidal Light 

provides surface decontamination and 

maintains sterility inside the enclosure.  It is located above the work area. 

7.

 

Variable PCR Digital UV Light Timer (Purifier PCR Enclosure only) 

allows the operator to time the surface disinfection of the work area for 
PCR protocols.  The UV light timer has eight settings of 5, 10, 15, 30, 60, 

Figure 4-1 

Features 

9, Internal 

10, Not 

Shown 

PCR 

Summary of Contents for Purifier 3951400





























Reviews: