Laars mascot ft MFTHW Installation And Operation Instructions Manual Download

Page: 1 / 96

Installation and Operation Instructions

Document 1342E

H2375000E

WARNING

If the information in this manual is not

followed exactly, a fire or explosion may

result causing property damage, personal

injury or loss of life.

Do not store or use gasoline or other

flammable vapors and liquids in the vicinity of

this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not

use any phone in your building.

• Immediately call your gas supplier from a

nearby phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call

the fire department.

Installation and service must be performed

by a qualified installer, service agency, or gas

supplier.

FOR YOUR SAFETY:

This product must be installed and serviced by a professional service technician,

qualified in hot water boiler and heater installation and maintenance. Improper installation and/or operation

could create carbon monoxide gas in flue gases which could cause serious injury, property damage, or

death. Improper installation and/or operation will void the warranty.

AVERTISSEMENT

Assurez-vous de bien suivres les instructions

données dans cette notice pour réduire au

minimum le risque d’incendie ou d’explosion

ou pour éviter tout dommage matériel, toute

blessure ou la mort.

Ne pas entreposer ni utiliser d’essence ou ni

d’autres vapeurs ou liquides inflammables dans

le à proximité de cet appareil ou de tout autre

appareil.

QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE

GAZ:

• Ne pas tenter d’allumer d’appareils.

• Ne touchez à aucun interrupteur. Ne pas vous servir

des téléphones dans le bâtiment où vous vous

trovez.

• Appelez immédiatement votre fournisseur de

gaz depuis un voisin. Suivez les instructions

du fournisseur.

• Si vous ne pouvez rejoindre le fournisseur de

gaz, appelez le sservice des incendies.

L’installation et l’entretien doivent être assurés par

un installateur ou un service d’entretien qualifié

ou par le fournisseur de gaz.

Installation and Operation
Instructions for

ASCOT

Wall-Mounted, Modulating
Gas, Condensing, Heating Only, Boiler
Model MFTHW

•

Natural Gas (NG) - Factory Configuration

•

Propane Gas (LP) - Field-Convertible

80,000 BTU/hr

100,000 BTU/hr

120,000 BTU/hr

140,000 BTU/hr

199,000 BTU/hr

Summary of Contents for mascot ft MFTHW

































































































Search results

Summary of Contents for mascot ft MFTHW

Reviews:

Related manuals for mascot ft MFTHW

Brands by name

Popular brands

Laars mascot ft MFTHW, Installation And Operation Instructions Manual

Search results

Summary of Contents for mascot ft MFTHW

Reviews:

Related manuals for mascot ft MFTHW

Brands by name

Popular brands