background image

9

EN

water supply line and the filtration system 

in order to eliminate any residual particles 

which could otherwise get stuck in taps or 

valves thus preventing them from working 

properly.  Connect  the  water  supply 

connection  of  the  espresso  machine  to 

the  water  pump  outlet  using  one  of  the 

supplied  stainless  steel  braided  hoses. 

Then connect the water pump inlet to the 

water filter/softener outlet (if present). 

 

Note: 

Make  sure  that  water  supply  is 

always  on  while  the  pump  is  operating, 

otherwise  air  can  be  introduced  into 

the  brew  boiler  causing  an  undesireable 

condition and damage to the pump.

3) Electrical connections

a) Power supply cord

• This is the main power supply cable that

provides  power  to  the  entire  espresso

machine.  There are different types of cable

based upon the electrical requirements of

the espresso machine purchased:

→  200/220VAC  1  Phase  3-core  cable  with 

2.5/4/6/10mm2 cross section or AWG 12/10/8 

(for UL version),  secured to espresso machine 

via a strain relief connector

→ 220VAC 3 Phase 4-core cable with 4 mm2 

cross  section  for  versions  with  1,  2  ,  3  and  4 

groups  secured  to  espresso  machine  via  a 

strain relief connector

→  380  VAC  3  Phase    5-core  cable  with  2.5/6 

mm2 cross section for versions with 1, 2, 3 and 

4  groups  secured  to  espresso  machine  via  a 

strain relief connector.

b) Water pump motor power cord

This  is  the  power  supply  for  the  water

pump motor.  The internal electronics will

switch the pump motor on when needed.

• 3-core cable with 1.5 mm2 cross section

or 3-core AWG 16 (for UL version) secured 

to  espresso  machine  via  a  strain  relief 

connector.

4) Waste water drain connection

The  espresso  machine  drain  is  to  be

connected  by  means  of  the  included

reinforced  plastic  tubing.  Connect  one

end  of  the  reinforced  plastic  tubing  to

the drain hose connection on the left side

of  the  espresso  machine,  secure  with

included hose clamp.

WARNING

THE MOTOR PUMP MUST BE SITUATED CLOSE 

TO THE MACHINE IN AN ACCESSIBLE PLACE 

FOR MAINTENANCE BUT NOT FOR 

ACCIDENTAL INTERFERENCE AND WHERE 

THERE IS AN OPTIMAL AIR CIRCULATION

WARNING

- U.S.A. AND CANADA ONLY -

DO NOT CONNECT TO A CIRCUIT 

OPERATING AT MORE THAN 150 V 

TO GROUND

WARNING

IN ORDER TO PREVENT CRACKS OR 

LEAKAGE: DO NOT STORE OR INSTALL

THE COFFEE MACHINE IN PLACES WHERE 

TEMPERATURE MAY CAUSE 

WATER IN BOILER OR 

HYDRAULIC SYSTEM TO FREEZE.

BEFORE MAKING ANY ELECTRICAL 

CONNECTIONS MAKE SURE THAT THE TWO 

STRAIN RELIEF CONNECTORS ARE FIRMLY 

SECURED TO THE BODY OF THE MACHINE IN 

ORDER TO PREVENT INADVERTENT STRESS 

ON THE POWER CABLES.

CAUTION

WARNING

THE MANUFACTURER DECLINES ANY 

RESPONSIBILITY  FOR ANY EVENT LEADING 

TO LIABILITY SUITS WHENEVER GROUNDING 

HAS NOT BEEN COMPLETED ACCORDING TO 

CURRENT LOCAL, NATIONAL, AND 

INTERNATIONAL REGULATIONS AND 

ELECTRICAL CODES, OR OTHER ELECTRICAL 

PARTS HAVE BEEN CONNECTED IMPROPERLY.

Summary of Contents for Linea
























Reviews: