background image

26 

 

Appendix A: Manufacturer’s Warranty 

All  La  Marche  Manufacturing  Co.  equipment  has  been  thoroughly  tested  and  found  to  be  in  proper  operating 
condition  upon  shipment  from  the  factory  and  is  warranted  to  be  free  from  any  defect  in  workmanship  and 
material that may develop within two (2) years from date of purchase under normal use. 
 
If  the  equipment  proves  defective  within  a  two  year  period,  it  shall  be  replaced  without  charge  after 
examination at our factory, providing such defect in our opinion, is due to faulty material or workmanship and 
not caused by tampering, abuse, misapplication or improper installation.  
 
Should the equipment require major replacement or repair, the equipment must be returned to the La Marche 
factory to have the inspections, parts, replacements and testing performed by factory personnel.  Should it be 
necessary to return a piece of equipment to the factory, the customer or Sales representative must first obtain a 
RMA (Return Material Authorization) from the factory.  If upon inspection at the factory, the defect was due to 
faulty material or workmanship, all repairs will be made at no cost to the customer during the warranty period.   
 
La Marche reserves the right to honor the warranty with a replacement unit. 
 
In  accepting  delivery  of  the  equipment,  the  purchaser  assumes  full  responsibility  for  proper  installation, 
installation adjustments and service arrangements.  Should minor adjustments be required, the local La Marche 
Sales Representative should be contacted to provide this service. 
 
All sales are final.  Only standard LaMarche units will be considered for return.  A 25% restocking fee is charged 
when return is factory authorized.  Special units are not returnable. 
 
In no event shall La Marche Manufacturing Co. have any liability for consequential damages, or loss, damage or 
expense directly or indirectly arising from the use of the products, or any inability to use them either separately 
or in combination with other equipment or materials, or from any other cause.  In addition, any alterations of 
equipment made by anyone other than La Marche Manufacturing Co. renders this warranty null and void. 
 
La  Marche  Manufacturing  Co.  reserves  the  right  to  make  revisions  in  current  production  of  equipment,  and 
assumes no obligation to incorporate these revisions in earlier models. 
 
The failure of La Marche Manufacturing Co. to object to provisions contained in customers' purchase orders or 
other communications shall not be deemed a waiver of the terms or conditions hereof, nor acceptance of such 
provisions. 
 
The  above  warranty  is  exclusive,  supersedes  and  is  in  lieu  of  all  other  warranties,  expressed  or  implied, 
including any implied warranty of merchantability or fitness.  No person, agent or dealer is authorized to give 
any  warranties  on  behalf  of  the  Manufacturer,  nor  to  assume  for  the  Manufacturer  any  other  liability  in 
connection with any of its products unless made in writing and signed by an official of the manufacturer. 

Summary of Contents for MXHF
































Reviews: