background image

 

12 

 

Technical Specifications (Cont…)

 

 

 

PROTECTION 

 

Current Walk-In

 

The output current will gradually increase after the inverter is turned on, 

eliminating surges and overshoot

 

Current Limit 

Overload protection 

Temperature 

Over Temperature Shutdown Protection 

ENVIRONMENTAL 

 

Operating 

Temperature 

32 to 122˚F (0 to 50˚C)

 

Relative Humidity 

0 to 95% (non-condensing) 

Cooling 

Fan Assisted 

Shock 

The inverter in its shipping container withstands shock developed when one edge 

of the container is dropped six inches while the opposite edge is resting on the 

ground, or it is dropped two inches without any physical damage or degradation 

of the electrical performance. 

Vibration 

The inverter in its shipping contained, withstands vibration encountered in 

shipping without physical damage or degradation of the electrical performance. 

Altitude 

The inverter is capable of operation at altitudes up to 2000 meters at an ambient 

temperature of up to +40 degrees C. 

Ventilation 

The unit should be mounted so that ventilating openings are not blocked and air 

entering the cabinet does not exceed 50 degrees C (122 degrees F). 

 

 
 

 

 

 

 

 
 

 

 

 

 
 

 

 

 

 

 
 

 

 

 

 

 
 

Summary of Contents for LTI2 PRO





















Reviews: