background image

 

22

3. 

Replace compartment cover. 

 

HOW TO INSTALL AND REPLACE BATTERIES IN THE TEMPERATURE TRANSMITTER 

The Temperature Transmitter uses 2 x AA, IECLR6, 1.5V batteries. To install and 
replace the batteries, please follow the steps below:

 

1. 

Slide the battery cover downwards and remove. 

2. 

Insert the batteries, observing the correct polarity (see marking). 

3. 

Replace the battery cover. 

 

Note: 

In the event of changing batteries in any of the units, all units need to be reset by 
following the setting up procedures. This is because a random security code is assigned 

by the transmitter at start-up and this code must be received and stored by the Temperature Station in the 
first three minutes of power being supplied to it. 

 

BATTERY CHANGE: 

It is recommended to replace the batteries in all units on an annual basis to ensure optimum accuracy of 
these units. 

 

Please participate in the preservation of the environment. Return used batteries to an 
authorized depot. 

 
LCD SCREEN 

The Temperature Station’s LCD is comprised of three lines and once the batteries are inserted, all the 
segments will light up momentarily before displaying:

 

Summary of Contents for WS-9014
















Reviews: