background image

H-17 • Radiant Heaters

www.lbwhite.com

Owner’s Manual • H-17

6

Propane gas and natural gas have man-made odor-
ants added speci

fi

 cally for detection of fuel gas leaks.

If a gas leak occurs, you should be able to smell the 
fuel gas .

THAT’S YOUR SIGNAL TO GO INTO IMMEDIATE 
ACTION!

  Do not take any action that could ignite the fuel 

gas. Do not operate any electrical switches. Do not 
pull any power supply or extension cords. Do not 
light matches or any other source of 

fl

 ame. Do not 

use your telephone.

  Get everyone out of the building and away from the 

area immediately.

    Close all propane gas tank or cylinder fuel supply 

valves, or the main fuel supply valve located at the 
meter if you use natural gas.

  Propane gas is heavier than air and may settle in 

low areas. When you have reason to suspect a 
propane leak, keep out of all low areas.

  Use your neighbor’s phone and call your fuel gas-

supplier and your 

fi

 re department. Do not re-enter 

the building or area.

  Stay out of the building and away from the area 

until declared safe by the 

fi

 re

fi

 ghters and your fuel 

gas supplier.

  FINALLY, let the fuel gas service person and the 

fi

 re

fi

 ghters check for escaped gas. Have them 

air out the building and area before you return. 
Properly trained service people must repair the 
leak, check for further leakages, and then relight 
the appliance for you.

  Some people cannot smell well. Some people 

cannot smell the odor of the man-made chemi-
cal added to propane or natural gas. You must 
determine if you can smell the odorant in these 
fuel gases.

  Learn to recognize the odor of propane gas and 

natural gas. Local propane gas dealers and your 
local natural gas supplier (utility) will be more than 
happy to give you a “scratch and sniff” pamphlet. 
Use it to become familiar with the fuel gas odor.

  Smoking can decrease your ability to smell. Being 

around an odor for a period of time can affect your 
sensitivity to that particular odor. Odors present in 
animal con

fi

 nement buildings can mask fuel gas 

odor.

 

  The odorant in propane gas and natural gas is col-

orless and the intensity of its odor can fade under 
some circumstances.

  If there is an underground leak, the movement of 

gas through the soil can 

fi

 lter the odorant.

  Propane gas odor may differ in intensity at different 

levels. Since propane gas is heavier than air, there 
may be more odor at lower levels.

  Always be sensitive to the slightest gas odor. If you 

continue to detect any gas odor, no matter how 
small, treat it as a serious leak. Immediately go into 
action as discussed previously.

Fuel Gas Odor

Safety Precautions

Odor Fading - No 

Odor Detected

WARNING

Asphyxiation Hazard

 Do not use this radiant heater for heating human living quarters.

 Do not use in unventilated areas.

 The 

fl

 ow of combustion and ventilation air must not be obstructed.

  Proper ventilation air must be provided to support the combustion air requirements of the heater 

being used.

  Refer to the speci

fi

 cation section of the Owner’s Manual, heater’s dataplate, or contact the LB 

White Company to determine combustion air ventilation requirements of the heater.

 Lack of proper ventilation air will lead to improper combustion.

  Improper combustion can lead to carbon monoxide poisoning in humans leading to serious injury 

or death. Symptoms of carbon monoxide poisoning can include headaches, dizziness and dif

fi

 culty 

in breathing.

  Symptoms of improper combustion affecting livestock can be disease, lower feed conversion, 

or death.

 

Summary of Contents for H-17





















































Reviews: