Kyocera TASKalfa 3051ci Page 237 Service Manual Download

Page: 237 / 317

2L6/2N6/2N5/2N4

1-4-236

4. DP-scanning second (back) page (with a reversed DP installed)

Defective part

Check description

Corrective Action

DP conveying pul-
ley

Check that the conveying pulley
is smoothly operative.

If the conveying pulley does not rotate
smoothly, re-asslemble the conveying roller
and springs.

Adjustment height
of the hinge
portions of the DP

Check the height of the front and
back portions of the DP.

If the front and back side of the DP is not
leveled, adjust the hinge on the left side.

Install DP

Check how DP is mounted on
the main unit.

If mounting to the main unit is improper, check
positioning and secure the screws.

DP hinge

Check that the DP hinge is
operative in both ascending and
descending directions and kept
open.

If the DP is not operative smoothly or is not
held stably open, replace the hinges.

DP document mat

Check the location the document
mat of the DP is mounted.

Re-mount the document mat of the DP if it is
hanged off.

Original document

Check that the leading edge of

the original document is dog-
eared.

If the leading edge of the original documet is
dog-eared, straighten.

Scanning guide

Check if the scanning guide is
distorted.

If the scanning guide deformed, replace.

Scopper guide

Check that the scopper guide is
smoothly operative.

If the scopper guide does not rotate smoothly,
re-install.

Conveying roller
(before and after
of scanning)

Check whether the conveying
roller is dirty.

If the conveying roller is dirty, clean.

Drive belt

Check if the drive belt is jumping
gear teeth.

If the drive belt is jumping gear teeth, re-mount
the belt tensioner.

Summary of Contents for TASKalfa 3051ci






























































































































































































































































































































Search results

Summary of Contents for TASKalfa 3051ci

Reviews:

Related manuals for TASKalfa 3051ci

Brands by name

Popular brands

Kyocera TASKalfa 3051ci, Service Manual

Search results

Summary of Contents for TASKalfa 3051ci

Reviews:

Related manuals for TASKalfa 3051ci

Brands by name

Popular brands