Kyocera PF-410 Service Manual Download Page 28 | Manualshive

Page: 28 / 55

background image

3HW

1-4-8

(1) The leading edge of

the image is consist-
ently misaligned with
the original.

Causes

1. Misadjusted leading edge registration.

Causes

Check procedures/corrective measures

1. Misadjusted leading edge registration.

Readjust the leading edge registration (see pages 1-5-7).

(2) The leading edge of

the image is sporadi-
cally misaligned with
the original.

Causes

1. Drawer paper feed clutch installed or

operating incorrectly.

Causes

Check procedures/corrective measures

1. Drawer paper feed clutch installed or

operating incorrectly.

Check the installation position and operation of the drawer paper
feed clutch. If any of them operates incorrectly, replace it.

«
...
26
27
28
29
30
...
»

Summary of Contents for PF-410
























































Reviews:

No comments

Related manuals for PF-410

Brand: Landoll Pages: 34

Brand: Bante Instruments Pages: 6

Brand: ICP DAS USA Pages: 45

Brand: unios Pages: 2

Brand: Palmer Pages: 2

Brand: M-system Pages: 4

INTRAmatic 31 ES

Brand: KaVo Pages: 52

Brand: Gomaco Pages: 30

Brand: Panduit Pages: 4

AutoMate 2500 series

Brand: Beckman Coulter Pages: 50

Brand: Grundig Pages: 16

Brand: KUHN Pages: 92

tynetec Aidcall

Brand: LEGRAND Pages: 6

Brand: SYSMEX Pages: 43

Brand: VWR Pages: 59

Brand: H&S Pages: 40

Brand: Defibtech Pages: 12

Signalmaster SMC14

Brand: Federal Signal Corporation Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands