Kyocera PF-410 Service Manual Download Page 18

Page: 18 / 55

Maintenance

Description

item No.

3HW

1-3-4

U031

Checking switches for paper conveying

Description

Displays the on-off status of each paper detection switch on the paper path.

Purpose

To check if the switches for paper conveying operate correctly.

Method

1. Press the start key.
2. Turn each switche on and off manually to check the status. When the on-status of a switch is detected, the

original size indicator corresponding to the operated switch lights.

Original size indicator

Switch

A3R/Ledger

Exit switch (ESW)

A5R/Legal

Registration switch (RSW)

A4/Letter-R

Drawer feed switch 1 (DFSW1)

B4R/Letter

Drawer feed switch 2 (DFSW2)

B5R/Statement

Feedshift switch (FSSW)

Folio/U

Duplex paper conveying switch (DUPPCSW)

Completion

Press the stop/clear key. The indication for selecting a maintenance item No. appears.

U032

Checking clutch operation

Description

Turns each clutch on.

Purpose

To check the operation of each clutch.

Method

1. Press the start key. A selection item appears.
2. Select the clutch to be operated using the copy exposure adjustment keys.
3. Press the start key. The selected clutch turns on for 1 s.

Display

Clutch

Paper feed clutch (PFCL)

Bypass paper feed clutch (BYPPFCL)

Drawer paper feed clutch 1 (DPFCL1)

Drawer paper feed clutch 2 (DPFCL2)

Drawer paper feed clutch 3 (DPFCL3)

Completion

Press the stop/clear key. The indication for selecting a maintenance item No. appears.

U034

Adjusting the print start timing

Adjustment

See pages 1-5-7 and 8.

U051

Adjusting the amount of slack in the paper

Adjustment

See page 1-5-9.

Summary of Contents for PF-410
























































Search results

Summary of Contents for PF-410

Reviews:

Related manuals for PF-410

Brands by name

Popular brands

Kyocera PF-410, Service Manual

Search results

Summary of Contents for PF-410

Reviews:

Related manuals for PF-410

Brands by name

Popular brands