Kyocera PF-410 Service Manual Download Page 7 | Manualshive

Page: 7 / 55

background image

• Do not pull on the AC power cord or connector wires on high-voltage components when removing

them; always hold the plug itself. ......................................................................................................

• Do not route the power cable where it may be stood on or trapped. If necessary, protect it with a

cable cover or other appropriate item. ..............................................................................................

• Treat the ends of the wire carefully when installing a new charger wire to avoid electric leaks. .......

• Remove toner completely from electronic components. ...................................................................

• Run wire harnesses carefully so that wires will not be trapped or damaged. ...................................

• After maintenance, always check that all the parts, screws, connectors and wires that were

removed, have been refitted correctly. Special attention should be paid to any forgotten
connector, trapped wire and missing screws. ..................................................................................

• Check that all the caution labels that should be present on the machine according to the

instruction handbook are clean and not peeling. Replace with new ones if necessary. ...................

• Handle greases and solvents with care by following the instructions below: ....................................

· Use only a small amount of solvent at a time, being careful not to spill. Wipe spills off completely.
· Ventilate the room well while using grease or solvents.
· Allow applied solvents to evaporate completely before refitting the covers or turning the main

switch on.

· Always wash hands afterwards.

• Never dispose of toner or toner bottles in fire. Toner may cause sparks when exposed directly to

fire in a furnace, etc. ..........................................................................................................................

• Should smoke be seen coming from the copier, remove the power plug from the wall outlet

immediately. ......................................................................................................................................

3. Miscellaneous

WARNING

• Never attempt to heat the drum or expose it to any organic solvents such as alcohol, other than

the specified refiner; it may generate toxic gas. ................................................................................

«
...
5
6
7
8
9
...
»

Summary of Contents for PF-410
























































Reviews:

No comments

Related manuals for PF-410

Brand: Velocitek Pages: 81

ABS-Lock X-Flat

Brand: ABS Pages: 8

ABS-Lock X-DURCH

Brand: ABS Pages: 8

Brand: ABS Pages: 8

Brand: Bartscher Pages: 28

Brand: Bartscher Pages: 13

Brand: IBEX Pages: 10

Brand: M-system Pages: 12

Brand: Rangevision Pages: 28

Brand: Dana Design Pages: 20

Brand: Garelick Pages: 2

Brand: Garelick Pages: 2

Brand: Gardigo Pages: 32

Brand: Nederman Pages: 255

Brand: Quark-Elec Pages: 2

Brand: Nakayama Pages: 14

2261998USBA1-XX

Brand: MMF POS Pages: 5

ARCHISHAPE 2.0 Linear

Brand: Osram Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands