Kyocera PF-410 Service Manual Download Page 20

Page: 20 / 55

Maintenance

Description

item No.

3HW

1-3-6

U901

Checking/clearing copy counts by paper feed locations

Description

Displays or clears copy counts by paper feed locations.

Purpose

To check the time to replace consumable parts. Also to clear the counts after replacing the consumable parts.

Method

1. Press the start key.
2. Select the paper feed location (group No.) for which the count is to be checked or cleared by lighting image

mode LEDs using the image mode selection key.

3. Select the item by lighting a copy exposure indicator using the copy exposure adjustment keys.

Image mode LED

Copy exposure

Copy quantity display (count value)

(group No.)

indicator

Exp. 1

First 3 digits of bypass copy count

Exp. 2

Last 3 digits of bypass copy count

Exp. 3

Clearing the count (CLE)

Exp. 1

First 3 digits of the drawer copy count

Exp. 2

Last 3 digits of the drawer copy count

Exp. 3

Clearing the count (CLE)

Exp. 1

First 3 digits of the first paper feeder copy count

Exp. 2

Last 3 digits of the first paper feeder copy count

Exp. 3

Clearing the count (CLE)

Exp. 1

First 3 digits of the second paper feeder copy count

Exp. 2

Last 3 digits of the second paper feeder copy count

Exp. 3

Clearing the count (CLE)

Exp. 1

First 3 digits of the third paper feeder copy count

Exp. 2

Last 3 digits of the third paper feeder copy count

Exp. 3

Clearing the count (CLE)

Exp. 1

First 3 digits of the duplex unit copy count

Exp. 2

Last 3 digits of the duplex unit copy count

Exp. 3

Clearing the count (CLE)

Exp. 1

Clearing all counts (CLE)

: Off,

: On,

: Flashing

Note: When no optional paper feed device is installed, the counts corresponding to optional paper feed

devices will not appear.

Clearing copy counts by paper feed locations

1. Select the paper feed location to clear the count.
2. Light exp. 3 using the copy exposure adjustment key.
3. Press the start key. The count is cleared.

Clearing copy counts for all paper feed locations

1. Select group 7.
2. Press the start key. The counts are cleared.

Completion

Press the stop/clear key. The indication for selecting a maintenance item No. appears.

Summary of Contents for PF-410
























































Search results

Summary of Contents for PF-410

Reviews:

Related manuals for PF-410

Brands by name

Popular brands

Kyocera PF-410, Service Manual

Search results

Summary of Contents for PF-410

Reviews:

Related manuals for PF-410

Brands by name

Popular brands