- 21 -
輔助把手(圖 5)
可將輔助把手 (9) 安裝到齒輪箱的任意一側。
操作
砂輪罩位置要適當。
千萬不要堵塞排風孔,以免影響馬達的冷卻。
研磨和砂光(圖 6)
有效操作的關鍵是控制砂輪片和工件之間的壓力和表面接觸。
平面要呈銳角研磨,一般與工件呈 15 至 30 度角。要待砂輪
片起動後達到全速時再研磨。角度過大會使壓力集中在小範
圍內,有時可造成凹口或燒壞工件。
切割
1. 用切割輪更換砂輪片。
2. 鬆開螺栓(18)並用切割輪罩(16)更換砂輪罩(2)。
然後,通過擰緊螺栓(18)來夾緊切割輪罩。
3. 在齒輪箱的任意一側安裝輔助把手。
把切割輪對準將要切割的物體,並將其緩慢放下。
移動工具不要加過份的壓力。
(壓力過大會使切割輪卡住 ,
導致切割粗糙。)
維修保養
使用後檢查工具確實仍處於良好狀態,建議每年至少到規定
的維修中心清潔和加油一次。
當馬達運轉時,切勿作任何調整。
在需要更換損壞的零件(刀片、鑽頭、砂紙等)和在工具的
工作部分加油以前,要把電源線插頭從插座上拔下。
防塵濾網的清理(圖 7)
使用後請拆下位於 2 處的防塵濾網 (19),清除附著於防塵濾
網上的異物與灰塵。
在附著異物的狀態下繼續使用,可能會造成冷卻風無法流動,
燒損馬達。
(拆下)
將防塵濾網的鉤扣(A)往箭頭①的方向推,同時往箭頭②的
方向拉起,以拆下防塵濾網。
(安裝)
將防塵濾網的突出處(B)對準機體的溝槽(C)插入,壓入
鉤扣(A)以完成安裝。
警告!
要確保安全和使用的可靠性,全部的修理工作,要到指定的
維修中心或品質可信的修理部進行。
請將本使用說明書妥為保存,以備需要時參考。
“
警告 :
必須一直佩帶防塵面具 , 聽覺保護器 , 護眼用具 ”
“
警告 :
為了減少受傷的風險,請務必閱讀操作手冊 ”
“
保護等級 II,具有不只依賴于基本絕緣,而且依賴
于雙重或強化絕緣等保護措施電擊保護的電動工具。 ”
Summary of Contents for AG1009
