background image

 

 

Contents 

 

10911 V01.06 

1

 

 

Contents 

 

CONTENTS  

----------------------------------------------------------------------------------------------------------- 

1

 

CHAPTER 1 

NOTES ON SAFETY AND USE, MAINTENANCE AND SERVICE -------------------- 4

 

 1.1

 

Safety notes ------------------------------------------------------------------------------------------------- 4

 

 1.2

 

Usage Notes ------------------------------------------------------------------------------------------------ 4

 

 1.3

 

Maintenance ------------------------------------------------------------------------------------------------ 4

 

 1.4

 

Cleaning ------------------------------------------------------------------------------------------------------ 5

 

 1.5

 

Calibration --------------------------------------------------------------------------------------------------- 5

 

 1.6

 

Service ------------------------------------------------------------------------------------------------------- 5

 

CHAPTER 2 

SPECIFICATIONS ---------------------------------------------------------------------------------- 6

 

CHAPTER 3 

CONTROL AND CONNECTION ELEMENTS, PIN CONFIGURATIONS ------------- 9

 

 3.1

 

Front Panel with Top and Bottom Section ----------------------------------------------------------- 9

 

 3.2

 

Rear panel ------------------------------------------------------------------------------------------------- 10

 

 3.3

 

USB-A socket --------------------------------------------------------------------------------------------- 10

 

 3.4

 

DVI output ------------------------------------------------------------------------------------------------- 11

 

 3.5

 

12V power supply ---------------------------------------------------------------------------------------- 11

 

CHAPTER 4 

STARTUP ------------------------------------------------------------------------------------------- 12

 

 4.1

 

Mains operation ------------------------------------------------------------------------------------------ 12

 

 4.2

 

Battery operation -----------------------------------------------------------------------------------------  12

 

 4.2.1

 

Replacing the battery ----------------------------------------------------------------------------------- 12

 

 4.2.2

 

Battery management ------------------------------------------------------------------------------------ 12

 

 4.3

 

Operation using an external power supply -------------------------------------------------------- 12

 

 4.4

 

Ventilation control ----------------------------------------------------------------------------------------  12

 

 4.5

 

Switching on ---------------------------------------------------------------------------------------------- 13

 

 4.6

 

Setting screen brightness and volume ------------------------------------------------------------- 13

 

CHAPTER 5 

MENU STRUCTURE -----------------------------------------------------------------------------  14

 

CHAPTER 6 

MEASURING RANGE --------------------------------------------------------------------------- 15

 

 6.1

 

Frequency input ------------------------------------------------------------------------------------------ 15

 

 6.1.1

 

IF input ----------------------------------------------------------------------------------------------------- 15

 

 6.1.2

 

RF input ---------------------------------------------------------------------------------------------------- 15

 

 6.1.2.1

 

Ku band ---------------------------------------------------------------------------------------------------- 15

 

 6.1.2.2

 

C band ------------------------------------------------------------------------------------------------------ 15

 

 6.2

 

DVB-S mode ---------------------------------------------------------------------------------------------- 16

 

 6.2.1

 

Symbol rate input ---------------------------------------------------------------------------------------- 16

 

 6.2.2

 

Scan --------------------------------------------------------------------------------------------------------- 16

 

 6.2.3

 

DVB-S parameters -------------------------------------------------------------------------------------- 16

 

 6.2.4

 

BER measurement (bit error rate measurement) ------------------------------------------------ 17

 

 6.2.5

 

MER measurement -------------------------------------------------------------------------------------- 17

 

 6.3

 

DVB-S2 mode -------------------------------------------------------------------------------------------- 17

 

 6.3.2

 

Scan --------------------------------------------------------------------------------------------------------- 17

 

 6.3.3

 

DVB-S2 parameters ------------------------------------------------------------------------------------- 18

 

 6.3.4

 

BER measurement (bit error rate measurement) ------------------------------------------------ 18

 

 6.3.5

 

MER measurement -------------------------------------------------------------------------------------- 18

 

 6.3.6

 

Packet error measurement ---------------------------------------------------------------------------- 18

 

 6.4

 

Level measurement ------------------------------------------------------------------------------------- 19

 

 6.4.1

 

MAX Hold function ---------------------------------------------------------------------------------------  19

 

 6.4.2

 

Acoustic level trend indicator ------------------------------------------------------------------------- 19

 

 6.5

 

LNB supply ------------------------------------------------------------------------------------------------ 19

 

 6.5.1

 

14/18 V – 22 kHz control -------------------------------------------------------------------------------  19

 

 6.5.2

 

DiSEqC -----------------------------------------------------------------------------------------------------  19

 

 6.5.2.1

 

DiSEqC V1.0 control ------------------------------------------------------------------------------------ 20

 

 6.5.2.2

 

DiSEqC V1.1 control ------------------------------------------------------------------------------------ 20

Summary of Contents for VAROS 109





























































Reviews: