background image

Instructions for assembly

GB

33

Electrical connection

• The electrical connection must be carried out by a quali-

fied electrician who is authorised to carry out such work!

• Statutory regulations and the connection specifications issued

by the local power supply company must be strictly observed.

• When connecting the appliance it must be ensured that there

is a device which makes it possible to disconnect it from the
mains at all poles with a contact opening width of at least
3 mm. Line-protecting switches, fuses or contactors are suita-
ble cut-out devices.
When connecting and repairing the appliance disconnect it
from the electricity supply with one of these devices.

• The earth wire must be sufficiently long so that if the strain

relief fails, the live wires of the connecting cable are subjected
to tension before the earth wire.

• Any superfluous cable must be removed from the installation

area beneath the appliance.

• Make sure that the local mains voltage is the same as the volt-

age on the rating label.

• Full protection against accidental contact must be ensured on

installation.

• Important! Incorrect connection may result in the power

electronics unit being destroyed.

Mains cable available in the factory

• The hob has been fitted with a temperature-resistant connec-

tion cable in the factory.

• Connection to the mains is carried out in accordance with the

circuit diagram, unless the connection cable is already fitted
with a plug.

• If the mains cable of this appliance is damaged it will need to

be replaced with a special connection cable. In order to avoid
any risks, this must be carried out by the manufacturer or his
Customer Service.

Electrical connections  

* Attention! Special power supply 

220 - 240 V 3~ !

Technical data

* Power when the power boost function is activated

Start of operation

Once the hob has been installed and the power supply has been
provided (mains connected) an automatic test of the controls will
be carried out and information for Customer Service will be indi-
cated.
Important: No items may be on the touch control sensor keys
when the appliance is being connected!

Briefly wipe over the surface of the hob with a sponge and soapy
water and then dry with a clean cloth.

gre

en-y

ellow

gre

en-y

ellow

blue

whi

te

brown

blac

k

gre

en-y

ellow

gre

en-y

ellow

blue

whi

te

brown

blac

k

gr

een-y

ellow

gr

een-y

ellow

blue

whit

e

brown

blac

k

gr

een-y

ellow

gr

een-y

ellow

blue

whit

e

brown

blac

k

Hob dimensions

Height/ Width/ Depth . . . . . . . mm 50 x 900 x 350

Cooking zones

left . . . . . . . . . . . . . . . .Ø cm / kW
center. . . . . . . . . . . . . .Ø cm / kW
right . . . . . . . . . . . . . .  Ø cm / kW

26/ 2.4 (3,2)*
18/ 1.85 (2,5)*
21/ 2.3 (3,2)*

Hob

 total . . . . . . . . . . . . . . . .  kW 6.9

Power supply

Mains voltage. . . . . . . . . . . . . . . .   . 380-415V 2N~, 50-60 Hz
Component rated voltage  . . . . . .   . 230 - 240V

Summary of Contents for EKI 9730.0-35F

















Reviews: