Kuppersbusch KD 6500.1, Instruction Booklet

Page: 9 / 24

9 GB
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
OPERATION
Instruction for Use
Control Panel (fig. 9)
The layout of the control panel is as follows:
Button
T1 = Turns the lighting system on and off
Button T2 = Turns the motor on and off
Button T3 = Decreases the working speed
Button T4 = Increases the working speed
Button T5 = Intensive speed with timed stoppage. Suitable to deal with maximum vapour
emission, this turns off automatically ten minutes after starting operation.
It can be disabled by pressing the button
T5 . Press T5 for approximately 3
seconds to enable the Power function (maximum suction power), which is
indicated by flashing of the LED over the button. This function will be revert
to intensive speed after 5 minutes or when
T5 is pressed again.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
MAINTENANCE
Constant maintenance guarantees proper operation and longterm reliability. Particular
attention should be paid to the metal grease filters and, for recirculation hoods only, to
the activated charcoal filters. The appliance is equipped with a system that indicates
automatically when it is time to carry out maintenance operations.
Metal grease filters
• Cleaning
These filters must be washed when LED Filters starts, or at the most once every 2
months, using a normal household detergent; their compact size also enables them to
be washed in a dishwasher.
• Removing the filters
Remove one filter at a time, pulling and turning the handle in an anticlockwise direction –
see
fig.10 . Replace by repeating the same operations in reverse order, making sure that
the handle is turned to face the outside.
• Enabling the alarm signal
The hood is already set up to trigger an alarm indicating saturation of the metal grease
filters, so this function does not need to be enabled.
• Resetting the alarm signal
To turn the alarm signal off, proceed as follows:
- Turn off the lights and the suction motor;
- Press the
T4 button for at least 3 seconds, until the LEDs flash in confirmation. In any
case the saturated filters alarm will only come into operation when the suction motor is
turned on.
WARNING: always comply with the maintenance and replacement times
indicated, in order to avoid a possible risk of fire when the filters are saturated
with grease.