KUHN GA 4511 GM, Assembly & Operators Manual

Page: 16 / 40

- 14 -
4° Fitting the warning boards and signalling elements
- Fit boards (A and A’) as shown on photo 12 using 6 screws (P) (M 10 x 20) and 6 self-locking nuts (M 10) on rear
support (C).
- Fit the rear left light (D), marked “L” , on the left board (A). The rear left light connector is also identified
by a white cable sheath (highlighted in grey on figure A).Connect it to electric harness (L) with the white
(highlighted in grey on figure A) plug (photo 13). The locking tab (1) of the female connector (2) must be fully
engaged over the peg (3) of the male connector (4) (fig. A).
- Fit the rear right light (D’), marked “R”, on board (A’) and connect to the electric harness (L). The locking tab (1)
of the female connector (2) must be fully engaged over the peg (3) of the male connector (4) (fig. A).
- Apply the two decals (E) on the outer lower corners of the boards (A and A’) (photo 12).
- Then set up the electric harness as shown on photos 12, 13 and 14. The harness is attached beneath the rear
support (C) using 4 clamp collars and self-adhesive collar holders (F).
At the front of the machine and along the beam, fit electric harness (L) to one of the hydraulic hoses (T) using 4
collars (S) (length 176 mm / 7") (photos 11 A and 14).
At the rear of the machine, fit electric harness (L) to the warning boards brackets using 4 clamp collars
and self-adhesive collar holders (V) (photo 13).
5° Fitting the swath board
Fit swath board (G) on support (H) using 2 screws (I) (M 10 x 30) (torque 5 daNm / 40 ft.lbs) and 2 self-locking nuts
(M 10) with 2 spacers (diameter 10.5 x 24 x 4) fitted between the guard (G) and the support (H) (photo 15).
6° Fitting tines, tine arm holders and tine arms
- Slide tine arms (L) into their holders (J) and attach using lynch pins (M) (photo 16).
- Attach the small loop of PVC cord (N) to lynch pin (M) then connect the big loop into bracket hole (O) on tine arm
(L) (photo 16).
- Fit holders (J) onto the oscillating shafts and attach using roll pins (K) (diameter 12 x 55 and diameter 7 x 55) (photo
16).
ATTENTION : Make sure that the roll pins are fitted 180° to each other and that the slots are facing the direction
of rotation (see drawing on photo 16).
NOTE : - On photo 16 the arrow indicates the direction of rotation of the rotor (looking from above).
- Fit the tine arms (L) onto the oscillating shafts (J) making sure that the bent form of the arms faces
forwards when looking in the direction of rotor rotation.
Clean and regularly apply "Never Seize" component to the removable portion of the tine
arms (L) (photo 16).
- Fit tines (Y) under tine arms (L) so that tines are slanting away from the direction of rotation (see arrow on
photo 17).
- The following items are needed to fit a tine : 1 screw (W) (M 12 x 70), 1 self-locking nut (Y) (M 12) (torque 8.5
daNm / 6 ft.lbs), 1 flat washer (Q) (13 x 35 x 5), 1 spring washer (X), 1 wedge (R).
Make sure all items are positioned correctly, as shown on photo 17.