KTI Networks KSC-240 Installation Manual Download Page 18 | Manualshive

Page: 18 / 43

background image

-18-

2.5 Applying Power

The power specifications of the device are:

Operating Voltage

+7 ~ +30VDC

Power Consumption Max. 0.6W @+30VDC, +12VDC, +7.5VDC

The device provides two types of power interfaces, terminal block and DC
power jack for receiving DC power input from external power supply.

Using Terminal Blocks

Either DC1 interface or DC2 interface can be used to receive DC power
from an external power system. Or, DC2 also can be used to deliver the
power received on DC1 to next device in cascading way.

DC1 +

Vdc Positive (+) terminal

DC1 -

Vdc Negative (-) terminal

DC2 +

Vdc Positive (+) terminal

DC2 -

Vdc Negative (-) terminal

Three 2P terminal plugs are provided together with the device. Two of the
three plugs are used for DC1 and DC2 interfaces respectively. The plug is
shown below:

«
...
16
17
18
19
20
...
»

Summary of Contents for KSC-240












































Reviews:

No comments

Related manuals for KSC-240

Brand: ABB Pages: 70

Brand: YMGI Pages: 64

Brand: Schumacher Pages: 11

Stratophonic SC3

Brand: Harman Kardon Pages: 6

Brand: Tvone Pages: 18

Brand: CYP Pages: 38

Brand: Vicon Pages: 18

Brand: FireBird Pages: 44

Brand: Vitek Pages: 12

Brand: MPP Solar Pages: 4

Sunny Island 3324

Brand: SMA Pages: 80

Brand: Badger Power Electronics Pages: 29

Brand: Must Pages: 10

Brand: Teleste Pages: 44

Brand: Alcad Pages: 9

Brand: ADF Web Pages: 30

Brand: GREISINGER Pages: 2

Brand: Kings Audio Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands