background image

English

n

Fill the water tank to the maximum line with fresh cold water and turn
the machine on 

(fig.1, 2, 3 and 4)

. While the machine is preheating,

the light will flash.

n

Using the measuring spoon, add 1 level spoon of espresso grounds
per cup of espresso 

(fig.5)

.

n

Remove any excess espresso grounds from the edge of the filter.

Important: 
Do not tamp the coffee down in the filter holder. The coffee
is automatically tamped to the optimum level by the Krups
Precise Tamp (KPT) system.

n

Insert the filter holder and turn the handle to the right as far as it will
go. You will hear a clicking sound as the Krups Precise Tamp (KPT)
system  automatically  adjusts  the  tamping  level  depending  on  the
amount  of  coffee  grounds  used.  The  handle  will  become
progressively harder to turn as you approach the optimum tamping
level, do not force the handle past this point. Use the “one cup” and
“two cup” markings on the brewing head as a guideline of where to
stop.  Because  the  Krups  Precise  Tamp  automatically  adjusts  the
tamping level, you may find that you do not always stop at the same
point each time. Never turn the handle past the far right edge of the
“one cup”marking 

(fig.7)

n

Put one or two cups under the filter holder as desired.

As  soon  as  the  required  temperature  is  achieved,  the  light  will  stop 
flashing.

n

Turn the dial to the

position 

(fig.8)

n

Press either the button 

for 1 cup or the 

button for 2 cups.

n

When the cups are filled with the desired amount of espresso, turn
the dial back to the 

position.

n

Unlock  the  filter  holder  by  pressing  the

button  on  the  handle

while turning the handle to the left to release, and remove the filter
holder from the machine.

n

Remove  the  used  espresso  grounds  using  the  ejection  system  by
holding the filter holder upside down over a trash receptacle. Press
the « 

PUSH

» button located between the two coffee outlet nozzles

on the underside of the filter holder 

(fig.12)

. Rinse the filter holder

under running water, pressing « 

PUSH

» while rinsing to release any

remaining grounds. Once the filter holder has been rinsed and dried
it can be refilled to prepare more espresso.

15

Summary of Contents for XP4600





























Reviews: