background image

EN

page 27

2.2.2 Operation

•   Insert the rack 

fi

 lled with dishes to wash. The plates must be correctly placed in the rack 

(see pict. 3).

 

Close the door. 

•   Select the wanted washing cycle (1, 2, 3, 

) by pushing the button 

"H"

 (see pict. 1). The 

display will show in sequence all available programs.

 

Once the wanted program is displayed, do release the button. 

 

The green LED 

"B"

 of the selected cycle lights up (1, 2, 3, 

).

•   Start the cycle by pushing the button 

"H"

 for not more than 1sec (see pict. 1). Starting 

of the cycle is signalled by the indicator of the selected cycle 

fl

 ashing. At the end of the 

cycle the indicator stops 

fl

 ashing and the message 

"END"

 appears on the display. 

•   The machine is ready for a new wash.
It is advisable to change the tank water, by means of another 

fi

 lling, at least every 40-50 

washes or twice a day.

N.B.:

 the machine does not accept other cycles until the door is opened or the button 

"H"

 

is pressed twice (see pict. 1).
The cycles (1, 2, 3, 

) are factory-set with times of 60 - 120 - 180 - 300 seconds.

2.2.3 Switching OFF

•   Turn the button 

"J"

. The machine will turn in 

"STAND-BY"

 mode (the red LED 

"E"

 comes 

ON).

•   Drain completely the wash-tank. Take off the over

fl

 ow pipe. For machines equipped with 

drain pump see par.

 2.5

•   Switch the main power switch OFF.
•   Shut the water valve.
•  At the end of the day, clean the machine (see chap. 

5 Maintenance

).

2.3 Detergent 

use

The detergent shall be the NO FOAM type, suitable for industrial dishwashers.
The use of good quality liquid detergents is recommended.
The detergent must be introduced in the tank. The amount is recommended by the manu-
facturers according to the water hardness. 
By request the dishwasher can be equipped with an electric detergent dispenser (always 
recommended).
1cm. of the product drawn into the tube is equal to about 0.15 g. A correct amount of deter-
gent is very important for a successful wash.
Should the detergent lack, the display will show 

"NO DE" 

(only with optional "Sensor for 

Chemicals Low Level").

pict. 3

2

3

1

DETERGENT

Summary of Contents for KP70EL




















Reviews: