background image

BIC · Edition 09.22

EN-14

8 AssIstAnCe In tHe eVent oF 
MALFUnCtIon

 DAnGeR

Electric shocks can be fatal!

 

– Before working on possible live components, 

ensure the unit is disconnected from the power 
supply.

 DAnGeR

Risk of injury!
Burner heads have sharp edges.

 

– Burner inspection must only be performed by 

authorized trained personnel.

 

If no issues are found when checking the burner, 
proceed to the automatic burner control unit and 
check for faults in accordance with the relevant 
operating instructions.

 ?  Fault
 ! 

 Cause
  •   Remedy

 ?  Burner does not function.
 ! 

 Valves do not open.
  •  Check the voltage supply and wiring.

 ! 

 Tightness control signals a fault.
  •  Check the valves for tightness.
  •  Note the tightness control operating instruc-

tions.

 ! 

 Control valves do not move to low-fire rate posi-

tion.

  •  Check the impulse lines.

 ! 

 Gas inlet pressure is too low.
  •  Check the filter for dirt.
  •  Check the gas supply.

 ! 

 Air inlet pressure is too low.
  •  Check the fan and air supply.

 ! 

 Gas and air pressures on the burner are too low.
  •  Check the restrictors.
  •  Check/adjust the start rate setting, see operat-

ing instructions for solenoid valve.

 ! 

 Automatic burner control unit does not function 

correctly.

  •  Check the device fuse.
  •  Note the automatic burner control unit operat-

ing instructions.

 ! 

 Automatic burner control unit signals a fault.
  •  Check the ionization cable.
  •  Check the ionization current. The ionization 

current must be at least 5 μA – stable signal.

  •  Check whether the burner is adequately 

grounded.

  •  Note the automatic burner control unit operat-

ing instructions.

 ! 

 No ignition spark is created.
  •  Check the ignition cable.

  •  Check the voltage supply and wiring.
  •  Check whether the burner is adequately 

grounded.

  •  Check the electrode – see  page 12 (7 

Maintenance).

 ! 

 Defective insulator on the electrode, ignition 

spark jumps over incorrectly.

  •  Check the electrode.

 ?  Burner performs a fault lock-out after oper-

ating faultlessly in normal operation.

 ! 

 Incorrect gas and air flow rate settings.
  •  Check the differential pressures for gas and air.

 ! 

 Automatic burner control unit signals a fault.
  •  Check the ionization cable.
  •  Check the ionization current. The ionization 

current must be at least 5 μA – stable signal.

 ! 

 Burner head is dirty.
  •  Clean gas and air bore holes and air slots.
  •   Remove  deposits.

 ! 

 Excessive pressure fluctuations in the combus-

tion chamber.

  •  Ask Honeywell Kromschröder for control 

concepts.

9 ACCessoRIes

9.1 Ceramic paste

For avoiding cold-setting on screw connec-
tions after replacing burner components. 

 

Order No.: 050120009. 

9.2 Adapter set

BIC 125 –140

BIC 50 –100

BICA 65

For connecting, burners BIC, BICA to NPT/ANSI con-
nections. 

Burner Adapt-

er set

Gas 

connec-

tion

Air 

connec-

tion

order 

no.

BIC 50

BR 50 

NPT

½"–14 

NPT

1½"–11.5 

NPT

74922630

BIC 65

BR 65 

NPT

¾"–14 

NPT

1½"–11.5 

NPT

74922631

BICA 

65*

½"–14 

NPT

Ø 1.89" 75456281

BIC 80

BR 80 

NPT

¾"–14 

NPT

2"–11.5 

NPT

74922632

BIC 100 BR 100 

NPT

1"–11.5 

NPT

2"–11.5 

NPT

74922633

BIC 125 BR 125 

NPT

1½"–11.5 

NPT

Ø 2.94" 74922634

BIC 140 BR 140 

NPT

1½"–11.5 

NPT

Ø 3.57" 74922635

* An NPT thread adapter is required for connection to the 

gas circuit only.

Adapted set for BICW on request. 

Summary of Contents for BIC 100

















Reviews: