KROHNE OPTISYS TUR 1060 Handbook Download Page 7

 SAFETY INSTRUCTIONS 

1

7

OPTISYS TUR 1060

www.krohne.com

01/2019 - 4007152501 - MA OPTISYS TUR 1060 R01 en

1.3  Safety instructions from the manufacturer

1.3.1  Copyright and data protection

The contents of this document have been created with great care. Nevertheless, we provide no 
guarantee that the contents are correct, complete or up-to-date.

The contents and works in this document are subject to copyright. Contributions from third 
parties are identified as such. Reproduction, processing, dissemination and any type of use 
beyond what is permitted under copyright requires written authorisation from the respective 
author and/or the manufacturer.

The manufacturer tries always to observe the copyrights of others, and to draw on works created 
in-house or works in the public domain.

The collection of personal data (such as names, street addresses or e-mail addresses) in the 
manufacturer's documents is always on a voluntary basis whenever possible. Whenever 
feasible, it is always possible to make use of the offerings and services without providing any 
personal data.

We draw your attention to the fact that data transmission over the Internet (e.g. when 
communicating by e-mail) may involve gaps in security. It is not possible to protect such data 
completely against access by third parties. 

We hereby expressly prohibit the use of the contact data published as part of our duty to publish 
an imprint for the purpose of sending us any advertising or informational materials that we have 
not expressly requested. 

1.3.2  Disclaimer

The manufacturer will not be liable for any damage of any kind by using its product, including, 
but not limited to direct, indirect or incidental and consequential damages. 

This disclaimer does not apply in case the manufacturer has acted on purpose or with gross 
negligence. In the event any applicable law does not allow such limitations on implied warranties 
or the exclusion of limitation of certain damages, you may, if such law applies to you, not be 
subject to some or all of the above disclaimer, exclusions or limitations. 

Any product purchased from the manufacturer is warranted in accordance with the relevant 
product documentation and our Terms and Conditions of Sale. 

The manufacturer reserves the right to alter the content of its documents, including this 
disclaimer in any way, at any time, for any reason, without prior notification, and will not be liable 
in any way for possible consequences of such changes.

Summary of Contents for OPTISYS TUR 1060

































































Reviews: