KROHNE BM 70 M Series Installation And Operating Instructions Manual Download Page 90

Page: 90 / 110

BM 70M-EEx/ BM 70Mi-EEx

unassigned

stainless steel (standard)

Type of waveguide window

H Hastelloy

Materials of wetted parts

SS stainless

steel

Hastelloy B (V96 only)

Hastelloy C (V96 only)

titanium (V96 only)

antennas and flanges including
coating

tantalum (V96 only)

K6375 Kalrez

6375

K4079 Kalrez

4079

K2035 Kalrez

2035

K1091 Kalrez

1091

FPM Viton

gasket materials

FEP

FEP sheathed gasket

Field of application, Device
Group II

Category 1G (use in Zone 0)

(1) places not needed in the type code may be omitted

3 Main

safety-relevant

characteristics

3.1 Signal

converter

The BM 70 M-EEx level gauges consist in each case of a combination of signal converter and
flange system. The main characteristics of the explosion-protected signal converter are
described below.

3.1.1 Category / Zone allocation

The signal converter part of the BM 70 M-EEx level gauges is basically designed in Category 2
for application in Zone 1.

3.1.2 Types of ignition protection

BM 70 M-EEx with non-intrinsically safe I/O functions

Variant

Device part

Type of protection

Symbol

Electronics compt

Flameproof Enclosure

Terminal compt

Increased Safety

BM 70 M/E-EEx

Pin coupler compt

Increased Safety

Electronics compt

Flameproof Enclosure

Terminal compt

Flameproof Enclosure

BM 70 M/D-EEx

Pin coupler compt

Increased Safety

EEx de

BM 70 M-EEx with intrinsically safe I/O functions

Variant

Device part

Type of protection

Symbol

Electronics compt

Flameproof Enclosure

Terminal compt

Increased Safety

BM 70 Mi/E-
EEx

Pin coupler compt

Increased Safety

Electronics compt

Flameproof Enclosure

Terminal compt

Flameproof Enclosure

BM 70 Mi/D-
EEx

Pin coupler compt

Increased Safety

EEx de [ia]

Summary of Contents for BM 70 M Series















































































































Search results

Summary of Contents for BM 70 M Series

Reviews:

Related manuals for BM 70 M Series

Brands by name

Popular brands

KROHNE BM 70 M Series, Installation And Operating Instructions Manual

Search results

Summary of Contents for BM 70 M Series

Reviews:

Related manuals for BM 70 M Series

Brands by name

Popular brands