background image

Type 

RA-2 HV3  

 

Operating Instructions 

DOK-208-GB.doc 

No. 0920-.., 

0921-... 

 

 

Automatic spray gun 

RA-2 HV3 

for adapter with 

material 

pressure regulator, 

article no. 

0909-080-0681

 

0921-090-2370 0921-090-2369 0921-090-2372 0921-090-2371 

 

 

 

3. Assembly

 

 

The assembly of the automatic spray gun type RA-2 HV3 depends on the intended 

application. We recommend the screw connection with the retaining bolt, art. no. 6922-080-

1256 as a standard fixing system. Further mounting/assembly options are shown in the 

diagram 140-0019 - e.g. mounting on the adapters (101 to 103). 

 

 

 

Note

 

 

If the automatic spray gun is not adequately secured, it may become loose during operation 

- e.g. due to vibrations. There is also a risk of displacement due to recoil. Under certain 

circumstances, the coating substance may escape in an uncontrolled manner. 
 

  Caution

 

Assembly should be performed by suitably trained personnel only! 

 

 

4. Startup 
 

4.1 Connections

 

 

 

Control air to input (St); (symbol stamped next to connection) 

 

Circular jet air to input (R); (symbol stamped next to connection) 

 

Flat jet air to input (F); (symbol stamped next to connection) 

 

Material connection to input (M); (symbol stamped next to connection) 

 

  

Caution  

 

Compressed air and material feed should only be connected up by suitably trained 

personnel! Ensure that the pressures and temperatures listed under "Technical Data" are 

not exceeded! 

 

 

 Notes 

 

 Air and material feed are connected via internal threads (e.g. nipple or nozzle-type  

    connection depending on application). If you not sure about the best connection method,  

    consult your supplier or Krautzberger GmbH. 
 

 Material feed can be effected via a container (under the intrinsic hydrostatic pressure of  

     the coating substance), a pressurised container or pumps. Circulation connection is  

     possible (e.g. when applying settling coating substances). 
 

 In the case of material feed under pressure (e.g. from pressure containers or via pumps),    

 

5

    ensure that the material feed is interrupted if the atomiser air pressure falls rapidly due   

Summary of Contents for 0920-090-2357




















Reviews: