![background image](http://html.mh-extra.com/html/kramer/vs-62h/vs-62h_user-manual_2001393039.webp)
Kramer Electronics Ltd.
VS-62H
– Protocol 3000
37
Function
Description
Syntax
Parameters/Attributes
Example
DISPLAY?
Get output HPD status.
COMMAND
#DISPLAY?
out_id
<CR>
FEEDBACK
~nn@DISPLAY
out_id
,
status
<CR><LF>
out_id
– Output number
1
– Output 1
2
– Output 2
status
– HPD status according to
signal validation
0
– Signal or sink is not valid
1
– Signal or sink is valid
2
– Sink and EDID is valid
Get the output HPD status of
Output 1:
#DISPLAY?
1
<CR>
DPSW-
STATUS?
Get the DIP-switch state.
COMMAND
#DPSW-STATUS?
dp_sw_id
<CR>
FEEDBACK
~nn@DPSW-STATUS
dp_sw_id
,
status
<CR><LF>
dp_sw_id
– 1 to number of DIP
switches
status
– Up/down
0
– up
1
– down
get the DIP-switch 2 status:
#DPSW-STATUS?
2
<CR>
ETH-PORT
Set Ethernet port
protocol.
COMMAND
#ETH-PORT
portType
,
ETHPort
<CR>
FEEDBACK
~nn@ETH-PORT
portType
,
ETHPort
<CR><LF>
portType
– TCP/UDP
ETHPort
– TCP/UDP port number
Set the Ethernet port protocol
for TCP to port 12457:
#ETH-PORT
0
,
12457
<CR>
ETH-PORT?
Get Ethernet port
protocol.
COMMAND
#ETH-PORT?
portType
<CR>
FEEDBACK
~nn@ETH-PORT
portType
,
ETHPort
<CR><LF>
portType
– TCP/UDP
0
– TCP
1
– UDP
ETHPort
– TCP / UDP port number
(0
– 65534)
Get the Ethernet port protocol
for UDP:
#ETH-PORT?
1
<CR>
FACTORY
Reset device to factory
default configuration.
This command
deletes all user data from
the device. The deletion
can take some time.
Your device may require
powering off and
powering on for the
changes to take effect.
COMMAND
#FACTORY
<CR>
FEEDBACK
~nn@FACTORY
OK
<CR><LF>
Reset the device to factory
default configuration:
#FACTORY
<CR>
FCT-MAC
Set MAC address.
To activate the
change, reset the device.
COMMAND
#FCT-MAC
mac_address
<CR>
FEEDBACK
~nn@FCT-MAC
mac_address
<CR><LF>
mac_address
– Unique MAC
address. Format: XX-XX-XX-XX-XX-
XX
where X is a hex digit
FCT-MODEL
Set model name.
Used where a single
firmware file is adaptable
for many devices, but the
user needs to know (by
protocol) which specific
model is used.
COMMAND
#FCT-MODEL
model_name
<CR>
FEEDBACK
~nn@FCT-MODEL
model_name
<CR><LF>
model_name
– String of printable
ASCII chars (up to 19 chars)
FCT-SN
Set serial number.
COMMAND
#FCT-SN
serial_number
<CR>
FEEDBACK
~nn@FCT-SN
serial_number
<CR><LF>
serial_number
– 14 decimal digits
FORMAT
Format file system.
Response could take
several seconds until
formatting completes.
COMMAND
#FORMAT
<CR>
FEEDBACK
~nn@FORMAT
OK
<CR><LF>
#FORMAT
<CR>
FS-FREE?
Get file system free
space.
COMMAND
#FS-FREE?
<CR>
FEEDBACK
~nn@FS_FREE
free_size
<CR><LF>
free_size
– Free size in device file
system in bytes
#FS-FREE?
<CR>
GEDID
Get EDID support on
certain input/output.
For old devices that
do not support this
command, ~
nn
@ERR
002
<CR><LF>
is
received.
COMMAND
#GEDID
stage
,
stage_id
<CR>
FEEDBACK
~nn@GEDID
stage
,
stage_id
,
size
<CR><LF>
stage
– Input/Output
0
– Input
1
– Output
2
– Default EDID
3
– Custom EDID
stage_id
– Number of chosen stage
(1 to max number of inputs/outputs)
size
– Size of data to be sent from
device, 0 means no EDID support
Get EDID support information
for input 1:
#GEDID
0
,
1
<CR>
GET
Get file.
COMMAND
#GET
file_name
<CR>
FEEDBACK
Multi-line:
~nn@GET
file_name
,
file_size
READY
<CR><LF>
contents
~nn@GET
file_name
OK
<CR><LF>
file_name
– Name of file to get
contents
contents
– Byte stream of file
contents
file_size
– Size of file (device
sends it in response to give user a
chance to get ready)
#GET
file_response.dat
<
CR>
HDCP-MOD
Set HDCP mode.
Set HDCP working
mode on the device input:
HDCP supported -
HDCP_ON [default].
HDCP not supported -
HDCP OFF.
HDCP support changes
following detected sink -
MIRROR OUTPUT.
COMMAND
#HDCP-MOD
inp_id
,
mode
<CR>
FEEDBACK
~nn@HDCP-MOD
inp_id
,
mode
<CR><LF>
inp_id
– Input number:
1
– IN 1
2
– IN 2
3
– IN 3
4
– IN 4
5
– IN 5
6
– IN 6
7
– IN 7
8
– IN 8
mode
– HDCP mode:
0
– HDCP Off
1
– HDCP On
Set the input HDCP-MODE of
IN 1 to Off:
#HDCP-MOD
1
,
0
<CR>