![background image](http://html1.mh-extra.com/html/kramer/multitools-850/multitools-850_user-manual_2001031028.webp)
850 - Serial Protocol
25
25
8.3.4
Set Output Status
Command
Send/Receive
Data
0xE6
0xEB, address, 0xE6, 0x02, data1, data2,
checksum
0xEB, address, 0xE6, 0x01, 0xFA,
checksum
data 1:
0x00: reserved
0x01: RESOULTION_INDEX
0x02: PATTERN_INDEX
0x03: DEEPCOLOR_MODE
0x04: COLORSPACE_MODE
0x05: reserved
0x06: AUDSAMPLE_INDEX
0x07: AUDBIT_INDEX
0x08: AUDCHANNEL_INDEX
0x09: BITRATE_INDEX
0x0A: OUT_LANE_INDEX
0x0B: OUT_ENHFRAMING_INDEX
0x0C: OUT_DELAY
0x0D: training
data 2:
reserved
from 0x00 to 0x17. (24 Resolutions)
from 0x00 to 0x1f. (32 Patterns)
0 = auto, 0x18 = 24bit, 0x1e = 30bit, 0x24 = 36bit
0 = auto, 1 = RGB444, 2 = YUV444, 3 = YUV422
reserved
0 = auto, 1 = 44k, 2 = 48k, 3 = 88k, 4 = 96k, 5 = 176k, 6 =
192k
0 = auto, 0x10 = 16bit, 0x14 = 20bit, 0x18 = 24bit
0 = auto, 1 = turn off, 2 = 2 channels, ……, 8 = 8 channels
0 = auto, 1 = 1.62G, 2 = 2.7G
0 = auto, 1 = 1 channel, 2 = 2 channels, 4 = 4 channels
0 = auto, 1 = not supported, 2 = supported
0 = 0ms, 1 = 200ms, 2 = 400ms, 3 = 600ms, 4 = 800ms, 5
= 1000ms
0 = training again
8.3.5
Get Output Status
Command
Send/Receive
Data
0xE7
0xEB, address, 0xE7, 0x01, 0x00, checksum
0xEB, address, 0xE7, 0x0E, data1,… data14,
checksum
Data1: FOLLOWENCRY_MONITOR;
0 = decryption, 1 = encryption
Data2: RESOULTION_INDEX;
from 0x00 to 0x17 (24 resolutions)
Data3: PATTERN_INDEX;
from 0x00 to 0x1f (32 patterns)
Data4: DEEPCOLOR_MODE;
0 = auto, 0x18 = 24bit, 0x1e = 30bit, 0x24 = 36bit
Data5: COLORSPACE_MODE;
0 = auto, 1 = RGB444, 2 = YUV444, 3 = YUV422
Data6: reserved
Data7: AUDSAMPLE_INDEX;
0 = auto, 1 = 44k, 2 = 48k, 3 = 88k, 4 = 96k, 5 = 176k,
6 = 192k
Data8: AUDBIT_INDEX;
0 = auto, 0x10 = 16bit, 0x14 = 20bit, 0x18 = 24bit
Data9: AUDCHANNEL_INDEX;
0 = auto, 1 = turn off, 2 = 2channels …..,8 = 8channels
Data10: BITRATE_INDEX;
0 = auto, 1 = 1.62G, 2 = 2.7G
Data11: OUT_LANE_INDEX;
0 = auto, 1 = 1, 2 = 2, 4 = 4 (channels)
Data12: OUT_ENHFRAMING_INDEX
0 = auto, 1 = not supported, 2 = supported.
Data13: OUT_DELAY;
0 = 0ms, 1 = 200ms, 2 = 400ms, 3 = 600ms, 4 = 800ms,
5 = 1000 (ms)
Data14: training result;
0 = fail, 1 = succeed