background image

 

Configuring and Maintaining the FC-21ETH,  
FC-22ETH and FC-24ETH

 

33 

 

Configuring and Maintaining the FC-21ETH,  
FC-22ETH and FC-24ETH  

This section describes: 

 

Selecting the RS-232 or RS-485 Port (se

Section

 

‎8.1

) 

 

Terminating the RS-485 bus (see 

Section

 

‎8.2

) 

 

Activating DHCP (se

Section

 

‎8.3

) 

 

Resetting to the factory default settings (se

Section

 

‎8.4

) 

 

Upgrading the firmware (se

Section

 

‎8.5

) 

8.1 

Selecting the RS-232 or RS-485 Serial Port 

The 3-pin Serial terminal block can be used as either an RS-232 or as an RS-485 

port. 

To set the Serial port as an RS-232 port: 

 

Release the RS-232/RS-485 button on the rear panel. 

The Serial RS-232 LED lights  

To set the Serial port as an RS-485 port: 

 

Depress the RS-232/RS-485 button on the rear panel. 

The Serial RS-485 LED lights 

8.2 

Terminating the RS-485 Bus 

The devices at both ends of the RS-485 chain must be terminated; all other devices 

in the chain must be left unterminated. 

To terminate the RS-485 bus

 

Slide the RS-485 Term switch down 

 

Summary of Contents for FC-21ETH





























































Reviews: