background image

30

9:37 Thu 22.04.2021

9:37 Thu 22.04.2021

Party/Holiday

Party/Holiday

PARTY/HOLIDAY (available in the system with cylinder)

Fast switching algorithm of work depending on 

the needs.

• 

PARTY: SET DURATION TIME [HOURS] (from 

1 to 24 hours or until the user’s change).

• 

HOLIDAY: SET DURATION TIME [DAYS] (from 

1 to 60 days or until the user’s change).

* If any of the above modes is ON then after entering PARTY/ HOLIDAY  there is a possibility to 

turn it off.

* The symbol of the activated mode is signalled on the main function screen.

In daily schedule CH circuit and DHW cylinder have defined starting time (3) and finishing 

time (4) of maintaining selected temperature value (5) in the room (CH) or DHW cylinder. 

Outside defined time frames economy temperature will be maintained in the room/cylinder. 

For circulation circuit within the schedule there is an adjustment of start time (3) and finish 

time (4) of circulation pump’s operation. In buffer mode there is an adjustment of start 

time (3) and finish time (4) of buffer’s charging. To change the parameters for the daily 

schedule select chosen program number and press navigation dial. 

The first parameter flashes (start time) - use the navigation dial to set the new time 

frame value (hour and minutes separately) by turning the dial left/right and confirm it by 

pressing the dial again. At the same time next screen starts to flash allowing edition of next 

parameters (finish time). Last editable position is a command. In order to save changes 

select command 

 and press the dial to finish editing. To delete selected time frame 

start editing chosen time frame and by pressing the dial go to command position, select 

command   and press the dial. To add new time frame, select last defined time frame 

and by pressing the dial go to command position, select command   and press the dial 

to add new time frame (edition of new time frames described above). 

DAILY SCHEDULE:

  1  -  time period panel

  2 - no. of time frame according to schedule 

(max 5)

  3  -  start time

  4  -  finish time

  5 - temperature selection (CH and DHW 

cylinder)

  6  -  command (active when editing):

    

 accept

    

 delete

    

 add

  

CH program                No1

CH program                No1

1  6:00  -  9:15  

2 15:20  -  22:15  

2 15:20  -  22:15  

2

3

4

5

6

1

End  

End  

Summary of Contents for HPM.Z









































Reviews: