Korenix JetNet 5728G series User Manual Download | Manualshive

Page: 90 / 134

background image

86

Feature

Command Line

IGMP Snooping
IGMP Snooping -
Global

Switch(config)# ip igmp snooping
IGMP snooping is enabled globally. Please specify on which

vlans IGMP snooping enables

IGMP Snooping - VLAN Switch(config)# ip igmp snooping vlan

VLANLIST allowed vlan list
all all existed vlan
Switch(config)# ip igmp snooping vlan 1-2
IGMP snooping is enabled on VLAN 1-2.

Disable IGMP Snooping
- Global

Switch(config)# no ip igmp snoopin
IGMP snooping is disabled globally ok.

Disable IGMP Snooping
- VLAN

Switch(config)# no ip igmp snooping vlan 3
IGMP snooping is disabled on VLAN 3.

Display – IGMP
Snooping Setting

Switch# sh ip igmp
interface vlan1
enabled: Yes
version: IGMPv1
query-interval; 125s
query-max-response-time: 10s

Switch# sh ip igmp snooping
IGMP snooping is globally enabled
Vlan1 is IGMP snooping enabled
Vlan2 is IGMP snooping enabled
Vlan3 is IGMP snooping disabled

Display – IGMP Table

Switch# sh ip igmp snooping multicast all
VLAN      IP Address                Type          Ports
----    ---------------      -------    ------------------------
      1            239.192.8.0      IGMP          fa6,
      1    239.255.255.250      IGMP          fa6,

IGMP Query
IGMP Query V1

Switch(config)# int vlan 1 (Go to management VLAN)
Switch(config-if)# ip igmp v1

IGMP Query V2

Switch(config)# int vlan 1 (Go to management VLAN)
Switch(config-if)# ip igmp

IGMP Query version

Switch(config-if)# ip igmp version 1
Switch(config-if)# ip igmp version 2

Disable

Switch(config)# int vlan 1
Switch(config-if)# no ip igmp

Display

Switch# sh ip igmp
interface vlan1

enabled: Yes

  version: IGMPv2
  query-interval: 125s
  query-max-response-time: 10s

Switch# show running-config
….
!
interface vlan1
  ip address 192.168.10.17/24

«
...
88
89
90
91
92
...
»

Summary of Contents for JetNet 5728G series







































































































































Reviews:

No comments

Related manuals for JetNet 5728G series

Brand: Water Witch Pages: 2

Brand: 3Com Pages: 2

CoreBuilder 5000

Brand: 3Com Pages: 16

CoreBuilder 9000

Brand: 3Com Pages: 24

Brand: Baxall Pages: 33

TECMA Silence Marine

Brand: Thetford Marine Pages: 9

Brand: Matrix Switch Corporation Pages: 60

Brand: FS Pages: 33

Brand: Cabletron Systems Pages: 110

Brand: NBK Pages: 32

Brand: S&S Northern Pages: 8

Brand: Comet Labs Pages: 46

Brand: Popp Pages: 9

InSwitch ISM-P Series

Brand: InHand Pages: 81

N.JGS516PE-100EUS

Brand: Duxbury Networking Pages: 4

Brand: NVision Pages: 92

Cross-8/HPoE-10G

Brand: Evidence Pages: 321

Brand: Ocean Matrix Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands