Korenix JetNet 5728G series User Manual Download | Manualshive

Page: 122 / 134

background image

118

Feature

Command Line

MAC Address Table
Ageing Time

Switch(config)# mac-address-table aging-time 350
mac-address-table aging-time set ok!

Note: 350 is the new ageing timeout value.

Add Static Unicast MAC
address

Switch(config)# mac-address-table static 0012.7701.0101

vlan 1 interface fastethernet7

mac-address-table ucast static set ok!

Note: rule: mac-address-table static MAC_address VLAN
VID interface interface_name

Add Multicast MAC
address

Switch(config)# mac-address-table multicast 0100.5e01.0101

vlan 1 interface fa6-7

Adds an entry in the multicast table ok!

Note: rule: mac-address-table multicast MAC_address
VLAN VID interface_list interface_name/range

Show MAC Address
Table – All types

Switch# show mac-address-table

***** UNICAST MAC ADDRESS *****
Destination Address    Address Type        Vlan          Destination Port
-------------------    --------------- -------    ------------------------
000f.b079.ca3b              Dynamic                  1                fa4
0012.7701.0386              Dynamic                  1                fa7
0012.7710.0101              Static                    1                fa7
0012.7710.0102              Static                    1                fa7
0012.77ff.0100              Management            1

***** MULTICAST MAC ADDRESS *****
Vlan      Mac Address          COS        Status      Ports
----      --------------- ----      ------- --------------------------
      1      0100.5e40.0800          0      fa6
      1      0100.5e7f.fffa          0      fa4,fa6

Show MAC Address
Table – Dynamic Learnt
MAC addresses

Switch# show mac-address-table dynamic

Destination Address    Address Type        Vlan          Destination Port
-------------------    --------------- -------    ------------------------
000f.b079.ca3b              Dynamic                  1                fa4
0012.7701.0386              Dynamic                  1                fa7

Show MAC Address
Table – Multicast MAC
addresses

Switch# show mac-address-table multicast

Vlan      Mac Address          COS        Status      Ports
----      --------------- ----      ------- --------------------------
      1      0100.5e40.0800          0      fa6-7
      1      0100.5e7f.fffa          0      fa4,fa6-7

Show MAC Address
Table – Static MAC
addresses

Switch# show mac-address-table static

Destination Address    Address Type        Vlan          Destination Port
-------------------    --------------- -------    ------------------------
0012.7710.0101              Static                    1                fa7
0012.7710.0102              Static                    1                fa7

Show Aging timeout
time

Switch# show mac-address-table aging-time
the mac-address-table aging-time is 300 sec.

Port Statistics
Port Statistics

Switch# show rmon statistics fa4 (select interface)

Interface fastethernet4 is enable connected, which has
Inbound:

«
...
120
121
122
123
124
...
»

Summary of Contents for JetNet 5728G series







































































































































Reviews:

No comments

Related manuals for JetNet 5728G series

FLOW BOSS VFB-DSU

Brand: VADA Pages: 17

Brand: Comtech EF Data Pages: 70

Brand: Pakedge Pages: 12

Brand: ADS Technologies Pages: 2

Brand: DX Engineering Pages: 4

Brand: Hama Pages: 36

Brand: Cabletron Systems Pages: 105

Brand: MCOHome Pages: 3

Brand: Smart-M Pages: 2

SIRCO MOT PV UL

Brand: socomec Pages: 20

Brand: Kramer Pages: 71

Brand: MaxLink Pages: 2

Brand: Quintum Pages: 79

Brand: ALZA Pages: 28

Matrix System150 WJ-SX155

Brand: Panasonic Pages: 5

AVHS400N - MULTI FORMAT LIVE SWITCHER

Brand: Panasonic Pages: 98

Brand: Panasonic Pages: 138

Hirschmann GREYHOUND GMM20

Brand: Belden Pages: 96

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands