Korenix JetNet 5728G series User Manual Download | Manualshive

Page: 117 / 134

background image

113

4.12 Monitor and Diag

JetNet 5728G provides several types of features for you to monitor the status of the switch
or diagnostic for you to check the problem when encountering problems related to the
switch. The features include MAC Address Table, Port Statistics, Port Mirror, Event Log
and Ping.

Following commands are included in this group:

4.12.1 MAC Address Table

4.12.2 Port Statistics

4.12.3 Port Mirror

4.12.4 Event Log

4.12.5 Topology Discovery

4.12.6 Ping

4.12.7 CLI Commands of the Monitor and Diag

4.12.1 MAC Address Table

JetNet 5728G provides 16K entries in MAC Address Table. In this page, users can change
the Aging time, add Static Unicast MAC Address, monitor the MAC address or sort them
by different packet types and ports. Click on Apply to change the value.

Aging Time (Sec)

Each switch fabric has limit size to write the learnt MAC address. To save more entries for
new MAC address, the switch fabric will age out non-used MAC address entry per Aging
Time timeout. The default Aging Time is 300 seconds. The Aging Time can be modified in
this page.

Static Unicast MAC Address

In some applications, users may need to type in the static Unicast MAC address to its MAC
address table. In this page, you can type MAC Address (format: xxxx.xxxx.xxxx), select its
VID and Port ID, and then click on Add to add it to MAC Address table.

MAC Address Table

In this MAC Address Table, you can see all the MAC Addresses learnt by the switch fabric.
The packet types include Management Unicast, Static Unicast, Dynamic Unicast, Static
Multicast and Dynamic Multicast. The table allows users to sort the address by the packet
types and port.

Packet Types: Management Unicast means MAC address of the switch. It belongs to
CPU port only. Static Unicast MAC address can be added and deleted. Dynamic Unicast
MAC is MAC address learnt by the switch Fabric. Static Multicast can be added by CLI
and can be deleted by Web and CLI. Dynamic Multicast will appear after you enabled
IGMP and the switch learnt IGMP report.

Click on Remove to remove the static Unicast/Multicast MAC address. Click on Reload to
refresh the table. New learnt Unicast/Multicast MAC address will be updated to MAC
address table.

«
...
115
116
117
118
119
...
»

Summary of Contents for JetNet 5728G series







































































































































Reviews:

No comments

Related manuals for JetNet 5728G series

Brand: CALIENT Pages: 22

Switch 4500 Family

Brand: 3Com Pages: 742

Brand: 3Com Pages: 940

Brand: 3Com Pages: 43

OfficeConnect WX1200

Brand: 3Com Pages: 646

Brand: D-Box Pages: 27

Brand: Techroutes Pages: 22

PU-8H8HBTPL-4K22

Brand: CYP Pages: 24

S3100-SI Series

Brand: H3C Pages: 58

Brand: REV Ritter Pages: 15

Brand: Cabletron Systems Pages: 194

Brand: Cabletron Systems Pages: 120

CentreCOM GS970M Series

Brand: Allied Telesis Pages: 21

Antenna-Disconnect-Switch

Brand: ADS Pages: 12

Brand: Black Box Pages: 4

Brand: Minicom DX Pages: 36

Brand: Origin Instruments Pages: 6

iBootBar iBB-DC8

Brand: Dataprobe Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands