Kontron coolMONSTER/C3 User Manual Download Page 90

Page: 90 / 90

KONTRON

Appendix H: Document Revision History

CMP/P3 and CMP/C3 User’s Guide

31.

APPENDIX G: DOCUMENT REVISION HISTORY

Version

Date

Edited by

Changes

LEU6M101

05.10.00

WKA

First preliminary release.

LEU6M110

06.02.01

WKA

First final release.

LEU6M111

05.03.01

WKA

Added warning for external battery.

Replaced PHLASH with JAP0034.

LEU6M113

26.03.01

WKA

Added Nordic warnings for lithium battery.

Added RS485 schematic.

LEU6M114

06.07.01

WKA

Added mechanical information.

LEU6M115

11.01.02

WKA

Corrected description feature connector Pin 14.

Added typical power consumption.

LEU6M116

18.03.02

WKA

Added and corrected height on bottom in mechanical

specification, power consumption on 850 MHz.

LEU6M117

23.04.02

WKA

•

Added height with bigger fan on 850 MHz on top.

•

Added slot restriction on blocking slots on some

backplanes.

•

Added operating temperature on 850 MHz.

•

Deleted reminder in Setup Security Menu.

•

Added Hardware Monitor and Temperature

Management Menu in Advanced Setup.

•

Added clock throttling description on 8.7 system

controller.

•

Removed external RTC battery pin on feature

connector.

•

Removed documentation part number

•

Removed information that manuals no longer

sold.

LEU6M118

03.05.02

DMA

Removed Virus Check Reminder in BIOS setup.
Removed PCI Device submenus in BIOS setup.
Added Temperature Management menu in BIOS
setup.
Added Hardware Monitoring menu in BIOS setup.

LEU6M119

16.05.02

DMA

Added Ultra DMA mode setup node in Master/Slave

submenus.

LEU6M11A

11.09.02

WKA

Added Ultra DMA mode setup node in Master/Slave

submenus.

LEU6M120

18.03.04

BHO/JL

Manual brought up to Kontron style.

Added drawings.

Added and corrected minor technical information.

LEU6M121

10.09.04

BHO

Corrected support addresses, removed USB boot devices,

added information about NC signals

LEU6M122

15.03.05

BHO

Added PISA bus chapter, added +3.3V information for

external PCI devices, update key is parallel port, minor

changes

Summary of Contents for coolMONSTER/C3



























































































Search results

Summary of Contents for coolMONSTER/C3

Reviews:

Related manuals for coolMONSTER/C3

Brands by name

Popular brands

Kontron coolMONSTER/C3, User Manual

Search results

Summary of Contents for coolMONSTER/C3

Reviews:

Related manuals for coolMONSTER/C3

Brands by name

Popular brands