Kontron coolMONSTER/C3 User Manual Download Page 3

Page: 3 / 90

KONTRON

CMP/P3 and CMP/C3 User’s Guide

Contents

CONTENTS

1. USER INFORMATION.............................................................................................. 1

1.1

About This Manual........................................................................................... 1

1.2

1.3

Trademarks.................................................................................................... 2

1.4

Standards...................................................................................................... 2

1.5

Warranty ....................................................................................................... 2

1.6

Technical Support ........................................................................................... 3

2. INTRODUCTION ...................................................................................................... 4

2.1

coolMONSTER/P3 and coolMONSTER/C3............................................................... 4

2.2

The coolMONSTER PISA® Family......................................................................... 4

3. GETTING STARTED ................................................................................................ 5

4. SPECIFICATIONS.................................................................................................... 6

4.1

Functional Specifications ................................................................................. 6

4.2

Mechanical Specifications................................................................................. 8

4.3

Electrical Specifications ................................................................................... 8

4.3.1.

Supply Voltage ............................................................................................ 8

4.3.2.

Supply Voltage Ripple ................................................................................... 8

4.3.3.

Supply Current (typical) ................................................................................ 8

4.3.4.

Supply Current (maximum) ............................................................................ 9

4.3.5.

Real-time Clock (RTC) Battery ......................................................................... 9

4.4

MTBF ...........................................................................................................10

4.5

Environmental Specifications ...........................................................................10

4.5.1.

Temperature ..............................................................................................10

4.5.2.

Humidity ...................................................................................................11

5. CPU, CHIPSET, AND SUPER I/O.......................................................................... 12

5.1

CPU.............................................................................................................12

5.2

Chipset ........................................................................................................12

5.3

Super I/O .....................................................................................................13

6. VIDEO CONTROLLER........................................................................................... 14

6.1

Video Subsystem Block Diagram........................................................................14

6.2

Supported Display Types..................................................................................15

6.2.1.

Current Panel Information ............................................................................15

6.2.2.

Available Video Modes .................................................................................15

7. SYSTEM MEMORY................................................................................................ 17

8. PISA BUS............................................................................................................... 18

9. FRONT PANEL ...................................................................................................... 19

Summary of Contents for coolMONSTER/C3



























































































Search results

Summary of Contents for coolMONSTER/C3

Reviews:

Related manuals for coolMONSTER/C3

Brands by name

Popular brands

Kontron coolMONSTER/C3, User Manual

Search results

Summary of Contents for coolMONSTER/C3

Reviews:

Related manuals for coolMONSTER/C3

Brands by name

Popular brands