Kongsberg XPR 100 Operator'S Manual Download Page 46

Page: 46 / 48

Seatex XPR 100

Procedure

Disconnect the power connector.

Open the fuse holder below the power inlet gently with a screw driver.

Within the holder there are two fuses, one in use and one spare. Remove the
innermost fuse and replace it with the spare fuse.

Close the fuse holder.

Connect the power connector and turn the power switch on.

WARNING

If the fuse has blown, the cause for the fuse failure must be
investigated.

Troubleshooting

Checking the signal history

If you are experiencing an unstable signal from the XPR system, you can check the
signal, range and bearing history.

Context

The

Target history

view displays signal, range and bearing graphs for the last 30 minutes.

If the signal is unstable, periods with invalid measurements are indicated with graphs
in the data range.

XPR-D-User/1.0

Summary of Contents for XPR 100

















































Search results

Summary of Contents for XPR 100

Reviews:

Related manuals for XPR 100

Brands by name

Popular brands

Kongsberg XPR 100, Operator'S Manual

Search results

Summary of Contents for XPR 100

Reviews:

Related manuals for XPR 100

Brands by name

Popular brands