manualshive.com logo in svg

Komfovent VERSO Pro P, Installation And Maintenance Service Manual

Share
Download
Komfovent VERSO Pro P Installation And Maintenance Service Manual Download Page 44

UAB KOMFOVENT we reserve the right to make changes without prior notice

V-C5.1_21-01

44

EN

Variable air volume control mode calibration:

1.  Before start of calibration the air distribution and exhaust devices in ventilation system should be 

adjusted, all valves for variable air flow in a way enabling air supply to all ventilated premises should 

be opened. 

2.  After switch on of the unit the VAV mode should be selected and calibration procedure should be 

confirmed. After the end of the calibration, depending on the configuration of pressure sensors, VAV 

mode status will change to Supply, Extract, Double.

3.  After calibration the air handling unit further will operate in the previous mode.

•  DCV

– direct controlled volume. The air handling unit will operate similarly as in the CAV mode, but 

air volumes will be maintained directly in accordance with the values of the B6 and B7 analog input 

signals of controller. After giving the signal 0... 10 V to the appropriate input, it will be converted 

according to the current determined air volume. For example, if the maximum air flow of the unit is 

1000 m

3

/h, setpoint in the panel – 800 m

3

/h, and the B6 input value – 7 V, the unit will supply con-

stant air volume of 560 m

3

/h, i. e., 70 % of the set value. The same applies to the exhaust air only by 

B7 input (see picture 5.3 b).

Time / Date

Time and date is required for air handling unit operation planning.

Also it is possible to activate automatic daylight saving time.

Enable

Daylight saving time

Time/Date

Time

09:40

Day/Month

25/05

Year

2019

Daylight saving time

On

Connectivity

• 

IP address and subnet mask. Setting is required when air handling unit is connected to PC network 

or Internet.

• 

Controller ID. Number that identifies the controller, when several air handling units are connected to 

common network and controlled by one control panel.

6.5.4.2. Personalization

In this item for the user are presented menu language, measurement units 

and other control panel settings. 

Personalization

Language

English

Flow units

m

3

/h

Screen saver

On

Panel lock

Off

Touch sound

Click

Summary of Contents for VERSO Pro P





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands