background image

UAB AMALVA we reserve the right to make changes without prior notice

50

EN

V2-C5-15-03-v1

Message

Possible cause

Elimination

Rotor motor overload

The rotor motor is overloaded.

Check the condition of the rotor motor and make 

sure that the rotor is not blocked.

Communication error

No communication with the internal com-

ponents of the air handling unit (controller 

extension modules, frequency converters, 

fans, etc.) or one / several of them are 

broken.

Check internal connections and functioning of 

separate components.

Controller failure

Main controller module fault.

Replace the main controller.

The emergency protection of the electrical heater against overheating can 

be reset with the RESET button only if the cause of the overheating of the 

heater has been clarified and eliminated.

If the unit is shut down and a red light diode is shining and a failure text 

message is shown on the control panel, the fault must be eliminated!

Before performing any jobs inside the unit make sure that the unit is 

stopped and disconnected from the electrical power supply.

After failure has been eliminated and power supply connected the error messages should be deleted. How-

ever if the failure has not been eliminated, unit either starts operating and after some time it stops again, or it does 

not operate and failure message is indicated.

Summary of Contents for VERSO-P



















































Reviews: