KOJA Future S Operation And Maintenance Instructions Download Page 4

Page: 4 / 41

FUTURE® S AIR HANDLING UNIT

OPERATION AND MAINTENANCE

INSTRUCTIONS

15 December 2020

Ver 1.7 (We reserve the right to changes without prior notice)

6.2 Safety ..................................................................................................................................................... 23
6.3 Installing ................................................................................................................................................ 23
6.4 Commissioning and maintenance ......................................................................................................... 23

7 Heat recovery section, rotating .................................................................................................................... 24

8 Electric automation ...................................................................................................................................... 30

9 Other accessories ......................................................................................................................................... 34

9.5.1 Pump group installation ................................................................................................................. 36
9.5.2 Pump group commissioning and maintenance .............................................................................. 36

9.6 Preheating coil for the duct (accessory) ................................................................................................ 37

9.6.1 Preheating coil installing, commissioning and maintenance ......................................................... 38

9.7 Cooling coil for the duct (accessory) ..................................................................................................... 38

9.7.1 Cooling coil installing, commissioning and maintenance ............................................................... 39

Summary of Contents for Future S










































Search results

Summary of Contents for Future S

Reviews:

Related manuals for Future S

Brands by name

Popular brands

KOJA Future S, Operation And Maintenance Instructions

Search results

Summary of Contents for Future S

Reviews:

Related manuals for Future S

Brands by name

Popular brands