background image

IMPORTANT INFORMATION

INSTRUCTIONS PERTAINING TO A RISK OF FIRE,

ELECTRICAL SHOCK, OR INJURY TO PERSONS

READ AND FOLLOW ALL INSTRUCTIONS

SAVE THESE INSTRUCTIONS

(CONT)

(

)

(RCD)

RCD

RCD

RCD

RCD

RCD

RCD

Never drop or insert any object into any opening.

The whirlpool bath must be connected only to a supply
circuit that is protected by a residual current device
(RCD). Such a RCD should be provided by the installer
and should be tested on a routine basis. To test the
RCD, press the test button. The RCD should interrupt
power. Press the reset button. Power should be
restored. If the RCD fails to operate in this manner, the
RCD is defective. If the RCD interrupts power to the
bath without the test button being pressed, a ground
current is flowing, indicating the possibility of an electric
shock. Do not use this bath. Disconnect the bath and
have the problem corrected by a qualified service
representative before using.

Use this whirlpool bath only for its intended purpose as
described in this manual. Do not use attachments
not recommended by the manufacturer.

!

!

!

!

!

!

(

)

Your new whirlpool bath is designed to stimulate,
invigorate, and energize your body. You will use the
following components:

!

!

Bath
Electronic Keypad
Nozzles
Water Pump
Electronic Drain
Water Pillow (optional)

!

!

!

!

YOUR KOHLER WHIRLPOOL BATH

4

1283904-T01-B

Summary of Contents for WHIRLPOOL














Reviews: