background image

5

111889-

CA

 (1093)

Kohler Co., Kohler WI

2.  PRODUCT NOTICES

A. INSTALLER HAZARD NOTIFICATION

DANGER: Risk of fire, electric shock, or injury
to persons. 
Read important safety instructions on
inside front cover of these instructions.

WARNING: Risk of electrical shock. A licensed
electrician should make all electrical connections.

WARNING: Risk of electrical shock. Connect
only to a circuit protected by a Ground-Fault
Circuit-Interrupter (GFCI). 

WARNING: Risk of electrical shock.
Disconnect power before servicing.

WARNING: Risk of injury or property damage.
Please read all instructions thoroughly before
beginning installation, including the following
Product Requirements.

NOTICE: Follow all local plumbing and electrical
codes.

B. FACTORY-ASSEMBLED FEATURES

K-852-V: Factory installed components include pump
with integral timer and air switch transmitter. No
installation is needed.

K-852-JA: Factory installed components include pump,
control and air switch transmitter.

The whirlpool pump and piping are factory-assembled.

WARNING: Unauthorized modification may
cause unsafe operation and poor performance
of the whirlpool.
 Do not relocate the whirlpool
pump or make other modifications to the whirlpool
system, as this could adversely affect the
performance and safe operation of the whirlpool.
Kohler Co. shall not be liable under its warranty or
otherwise for personal injury or damage caused by
any such unauthorized modification.

Summary of Contents for Tea-For-Two K-852-JA-AA

















Reviews: