background image

CASES OF EXCLUSION FROM THE WARRANTY:

Warranty exclusion applies in the following cases: damage resulting from transporting the unit; incorrect installation or installation 
not complying with 

SDMO Industries

 recommendations and/or technical and safety standards; use of non-recommended products, 

components, replacement parts, fuel or lubricants; incorrect use or misuse of the unit; modification or conversion of the unit or any 
of its components not authorized by 

SDMO Industries

; normal wear and tear of the unit or of one of its components; damage due to 

negligence, failure to monitor, service or clean the unit; force majeure, acts of God or other external causes (natural disaster, fire, 
impact, flooding, lightning, etc.); operation of the unit with insufficient load; inadequate storage conditions of the unit. The following 
components are also excluded from the warranty: the starter systems (batteries, starter motors, starter), the filters, the belts, the 
fuses, the switches, the lamps, the commutators, and all consumables and wearing parts.

TERMS AND CONDITIONS FOR APPLICATION: 

The  warranty  must  be  applied  by  the  distributor  from  which  you  purchased  your  unit.  You  are  requested  by 

SDMO  Industries

  to 

locate  your  purchase  invoice  and  contact  the  distributor  or,  where  applicable,  the  Customer  Service  Department  of 

SDMO 

Industries

. Staff from this department can answer your questions concerning the warranty’s application conditions; contact details 

are  as  follows:  SDMO  Industries,  270  rue  de  Kerervern  –  29490  GUIPAVAS  /  CS 40047-  29801  BREST  CEDEX  9 – 
Tel: France 0.806.800.107 (call charge) – Fax: +33298416307.

LEGAL GUARANTEES

Information  for the consumer, who is defined  as any individual acting for purposes outside of his or her trade,  business, craft  or 
profession.

SDMO Industries

 is liable for any conformity issues with your unit under the conditions set out in article L. 211-4 and following of the 

Consumer Code and for hidden defects in the sold item under the conditions set out in articles 1641 and following of the civil code. 
Under the conformity guarantee: 

-

you  have  a  period  of  2  years  from  the  date  your  unit  was  delivered  to  make  a  claim  under  the  statutory  conformity 
guarantee.

-

you  may  choose  between  repair  or  replacement  of  your  unit,  subject  to  the  conditions  set  out  in  article  L.  211-9  of  the 
Consumer Code.

-

you are required to send proof of the existence of the conformity issue with your unit within 6 months of the item's delivery. 
This period is extended to 24 months from 18 March 2016; this does not apply to used items. 

The statutory guarantee applies independently of the commercial warranty provided by 

SDMO Industries

You may also decide to implement the guarantee applicable to hidden defects with your unit under the conditions set out in article 
1641 of the Civil Code. If there is a hidden defect with your unit, and you are required to provide proof, you may choose between 
cancellation of the sale or a reduction in the sale price in accordance with article 1644 of the Civil Code. 

Articles of the Consumer Code

Article L211-4
The vendor is required to deliver goods that comply with the contract and is answerable for any non-compliances existing 
on delivery. 

It is also answerable for any non-compliances resulting from packing, assembly instructions or installation when in the 

charge of the latter under the terms of the contract or when carried out under its responsibility.

Article L211-5

To comply with the contract, the goods must:
1. Be suitable for the use customarily expected of similar goods and, if applicable, must:

-

match the description given by the Vendor and possess the qualities that the Vendor has presented to the Buyer in the 
form or a sample or model;

-

have the qualities a Buyer can legitimately expect, considering the public statements made by the Vendor, the producer or 
its representative, particularly in its advertising or labeling;

2. Or alternatively, present the characteristics mutually defined by the parties or be suitable for any special purpose desired by the 
Buyer which has been made known to the Vendor and which the Vendor has accepted.

Article L211-12

Action arising from a non-compliance is limited to a period of two years from the date of delivery of the goods.

Article L.211-16

When, during the term of the commercial warranty granted to the Buyer when the goods were purchased or repaired, the Buyer 
requests a repair from the Vendor which is covered by the warranty, any period of immobilisation of seven days or more shall be 
added to the remaining term of the warranty. This period shall apply from the date the Buyer requests that work is performed or 
when the goods in question were made available for repair, if this second date precedes the request for the work to be performed.

Articles of the Civil Code

Article 1641

The vendor is bound by the warranty for any hidden defects in the item sold which make it unsuitable for its intended purpose or 
which limit the said purpose to such an extent that the purchaser would not have acquired it, or would only have paid a lower price 
had they been aware of it.

Article 1648 sub-paragraph

 

1

The purchaser must instigate action resulting from unacceptable defects within two years of discovering the defect.

22/22

Summary of Contents for SDMO PERFORM 3000 XL TB UK C5















Reviews: