Kohler PW 6000 User Manual Download Page 37

Page: 37 / 74

UPS413-01-00 Kohler PW 6000 (60-500kVA) User Manual 25 June 2012

3-19

3: Installation

Set DIP switch SW2-2 on each parallel adaptor board according to the position of the UPS cabinet in the
parallel configuration

(See Figure 3.12)

Connect a bus-cable between PORT JD6 of UPS cabinet 1 parallel adaptor and PORT JD5 of UPS
cabinet 2 parallel adaptor.

Connect a bus-cable between PORT JD6 of UPS cabinet 2 parallel adaptor and PORT JD5 of UPS
cabinet 3 parallel adaptor.

Continue with the above steps until a Bus-cable is connected to all modules, as shown below.

Figure 3.12 Bus-lines connections (3 Modules shown)

3.9.2 Configuration DIP switch selection

DIP Switch SW1-9

DIP Switch SW1-9 on the UPS communications interface board

(See Figure 3.13)

must be set to indicate the

position of the cabinet in the parallel chain. The three options are:

• First cabinet.
• Middle cabinet (there may be several ‘middle’ cabinets).
• Last cabinet.

In each cabinet, set Switch SW1-9 according to the table below:

SW1-9

Single Cabinet

First Cabinet

Middle Cabinet

Last Cabinet

OFF

Master-Slave

Output

JD6

Master-Slave

Input

JD5

UPS Cabinet 1

Master-Slave

Output

JD6

Master-Slave

Input

JD5

UPS Cabinet 2

Master-Slave

Output

JD6

Master-Slave

Input

JD5

UPS Cabinet 3

Parallel Adaptor

SW2-2

Master-Slave

Output

JD6

Master-Slave

Input

JD5

Parallel Adaptor

SW2-2

Single Cabinet

First Cabinet

Middle Cabinet

Last Cabinet

SW 2-1

OFF

SW 2-2

OFF

SW2-2 Configuration
Switch

Parallel adapter board
fitted to JD8 on UPS
communications

JD6

JD5

interface board

Summary of Contents for PW 6000











































































Search results

Summary of Contents for PW 6000

Reviews:

Related manuals for PW 6000

Brands by name

Popular brands

Kohler PW 6000, User Manual

Search results

Summary of Contents for PW 6000

Reviews:

Related manuals for PW 6000

Brands by name

Popular brands