Kohler KDI-2504TCR Owner'S Manual Download Page 40

8

40

EN

INFORMATION ABOUT WARRANTY

WARRANTY INTERNATIONAL  

Please refer to the generator set warranty

WARRANTY NORMS EPA

KOHLER CO. 

CALIFORNIA AND FEDERAL EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND 

OBLIGATIONS

The California Air Resources Board, U.S. Environmental Protection Agency (“EPA”) and Kohler Co. are pleased to explain the 
emission control system warranty on your MY2014-2016 engine. In California (“the State”) and US EPA regulated applications, 
new heavy-duty off-road engines must be designed, built and equipped to meet the State's and U.S EPA’s stringent anti-smog 
standards. Kohler Co. must warrant the emission control system on your engine for the periods of time listed below provided 
there has been no abuse, neglect or improper maintenance of your engine.

Your emission control system may include parts such as the fuel injection system and the air induction system. Also included 
may be hoses, belts, connectors and other emission-related assemblies.

Where a warrantable condition exists, Kohler Co. will repair your heavy-duty off-road engine at no cost to you including 
diagnosis, parts and labor.

MANUFACTURER'S WARRANTY COVERAGE

The MY2014-2016 heavy-duty off-road engines are warranted for the periods listed below. If any emission-related part on your 
engine is defective, the part will be repaired or replaced by Kohler Co.

OWNER'S WARRANTY RESPONSIBILITIES

1. 

As the off-road engine owner, you are responsible for the performance of the required maintenance listed in your owner's 
manual. Kohler Co. recommends that you retain all receipts covering maintenance on your off-road engine, but Kohler 
Co. cannot deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled 
maintenance.

2. 

As the off-road engine owner, you should however be aware that Kohler Co. may deny you warranty coverage if your off-
road engine or a part has failed due to abuse, neglect, improper maintenance or unapproved modifications.

3. 

Your engine is designed to operate on diesel fuel only. Use of any other fuel may result in your engine no longer operating 
in compliance with California's emissions requirements.

4. 

You are responsible for initiating the warranty process. The ARB suggests that you present your off-road engine to a 
Kohler Co. dealer as soon as a problem exists. The warranty repairs should be completed by the dealer as expeditiously 
as possible.

If you have any questions regarding your warranty rights and responsibilities, you should contact Kohler Co., by visiting  

www.kohlerengines.com

 or telephone 1-800-544-2444 (U.S.A. and Canada).

MY2014-2016 KDI ENGINES

ENGINE POWER

DURATION

kW < 19 (hp < 25)

3 years or 6,000 hours

kW ≥ 19 (hp ≥ 25)

5 years or 6,000 hours

MY2014-2016 KD, KDW AND ALL TPEM ENGINES

ENGINE POWER

DURATION

kW < 19 (hp < 25)

3 years or 2,000 hours

kW ≥ 19 (hp ≥ 25)

5 years or 3,000 hours

Summary of Contents for KDI-2504TCR

















































Reviews: